feature-remoteid/RemoteIDModule/board_config.h

/*
  board configuration file
*/

#pragma once

#define GB_UAV_REMOTEID 1

#ifdef BOARD_ESP32S3_DEV
#define BOARD_ID 1
// #define PIN_CAN_TX GPIO_NUM_47
// #define PIN_CAN_RX GPIO_NUM_38
#define PIN_CAN_TX GPIO_NUM_5
#define PIN_CAN_RX GPIO_NUM_4
#define PIN_UART_TX 18
#define PIN_UART_RX 17

// #define WS2812_LED_PIN GPIO_NUM_48
#define WS2812_LED_PIN GPIO_NUM_38

#elif defined(BOARD_ESP32C3_DEV)
#define BOARD_ID 2
#define PIN_CAN_TX GPIO_NUM_5
#define PIN_CAN_RX GPIO_NUM_4

#define PIN_UART_TX 3
#define PIN_UART_RX 2

#define WS2812_LED_PIN GPIO_NUM_8

#elif defined(BOARD_BLUEMARK_DB200)
#define BOARD_ID 3

#define PIN_CAN_TX GPIO_NUM_0 // this goes to the TX pin (= input) of the NXP CAN transceiver
#define PIN_CAN_RX GPIO_NUM_5
#define PIN_CAN_EN GPIO_NUM_4 // EN pin of the NXP CAN transceiver
#define PIN_CAN_nSILENT GPIO_NUM_1 // CAN silent pin, active low

#define CAN_APP_NODE_NAME "BlueMark DB200"

// to enable termination resistors uncomment this line
//#define PIN_CAN_TERM GPIO_NUM_10 // if set to ON, the termination resistors of the CAN bus are enabled

#define PIN_UART_TX 3
#define PIN_UART_RX 2

#define PIN_STATUS_LED GPIO_NUM_8 // LED to signal the status
// LED off when ready to arm
#define STATUS_LED_OK 0

#elif defined(BOARD_BLUEMARK_DB110)
#define BOARD_ID 4
#define PIN_UART_TX 5
#define PIN_UART_RX 4

#define PIN_STATUS_LED GPIO_NUM_8 // LED to signal the status
// LED off when ready to arm
#define STATUS_LED_OK 0

#elif defined(BOARD_JW_TBD)
#define BOARD_ID 5
#define PIN_CAN_TX GPIO_NUM_47
#define PIN_CAN_RX GPIO_NUM_38

#define PIN_UART_TX 18
#define PIN_UART_RX 17

#define PIN_STATUS_LED GPIO_NUM_5 // LED to signal the status
#define LED_MODE_FLASH 1 // flashing LED configuration
// LED on when ready to arm
#define STATUS_LED_OK 1

#define CAN_APP_NODE_NAME "JW TBD"

#elif defined(BOARD_MRO_RID)
#define BOARD_ID 6
#define PIN_CAN_TX GPIO_NUM_0
#define PIN_CAN_RX GPIO_NUM_1

#define PIN_UART_TX 4
#define PIN_UART_RX 5

#define WS2812_LED_PIN GPIO_NUM_2
#define CAN_APP_NODE_NAME "mRobotics RemoteID"

#elif defined(BOARD_JWRID_ESP32S3)
#define BOARD_ID 7
#define PIN_CAN_TX GPIO_NUM_47
#define PIN_CAN_RX GPIO_NUM_38

#define PIN_UART_TX 37
#define PIN_UART_RX 36

#define WS2812_LED_PIN GPIO_NUM_5

#define CAN_APP_NODE_NAME "JWRID_ESP32S3"

#elif defined(BOARD_BLUEMARK_DB202)
#define BOARD_ID 8

#define PIN_UART_TX 7
#define PIN_UART_RX 6

#define PIN_STATUS_LED GPIO_NUM_8 // LED to signal the status
// LED off when ready to arm
#define STATUS_LED_OK 0

#elif defined(BOARD_BLUEMARK_DB210)
#define BOARD_ID 10
#define PIN_CAN_TX GPIO_NUM_19
#define PIN_CAN_RX GPIO_NUM_20

#define PIN_UART_TX 7
#define PIN_UART_RX 6
//#define PIN_UART_CTS 15 //not used, perhaps useful if TELEM 1 is used for different purpose
//#define PIN_UART_RTS 16 //not used, perhaps useful if TELEM 1 is used for different purpose

//#define PIN_UART_TX_2 2 //TELEM 2
//#define PIN_UART_RX_2 1 //TELEM 2
//#define PIN_UART_CTS_2 5 //TELEM 2, not used, perhaps useful if TELEM is used for different purpose
//#define PIN_UART_RTS_2 4 //TELEM 2, not used, perhaps useful if TELEM is used for different purpose

#define BUZZER_PIN GPIO_NUM_39 //at the moment easiest is to have active buzzer support. (Buzzer on if GPIO is high)

#define WS2812_LED_PIN GPIO_NUM_8 //there are two WS2812 LEDs on this GPIO

#define CAN_APP_NODE_NAME "BlueMark DB210PRO"
//#define PIN_CAN_TERM GPIO_NUM_42 // if set to ON, the termination resistors of the CAN bus are enabled

#elif defined(BOARD_BLUEMARK_DB203)
#define BOARD_ID 9

#define PIN_CAN_TX GPIO_NUM_6
#define PIN_CAN_RX GPIO_NUM_7

#define PIN_UART_TX 5 // not used, but needed to avoid compilation errors
#define PIN_UART_RX 4 // not used, but needed to avoid compilation errors

#define CAN_APP_NODE_NAME "BlueMark DB203"


#define PIN_STATUS_LED GPIO_NUM_8 // LED to signal the status
// LED off when ready to arm
#define STATUS_LED_OK 0

#elif defined(BOARD_Holybro_RemoteID)
#define BOARD_ID 11
#define PIN_CAN_TX GPIO_NUM_5
#define PIN_CAN_RX GPIO_NUM_4

#define PIN_UART_TX 3
#define PIN_UART_RX 2

#define WS2812_LED_PIN GPIO_NUM_8

#elif defined(BOARD_CUAV_RID)
#define BOARD_ID 12
#define PIN_CAN_TX GPIO_NUM_47
#define PIN_CAN_RX GPIO_NUM_38
#define PIN_CAN_nSILENT GPIO_NUM_1

#define PIN_UART_TX 18
#define PIN_UART_RX 17

#define WS2812_LED_PIN GPIO_NUM_48

#define PIN_CAN_TERM GPIO_NUM_37
#define CAN_TERM_EN  LOW
#define CAN_APP_NODE_NAME "net.cuav.c-rid"

#elif defined(BOARD_VKUAV_RID)

#define BOARD_ID 13
#define PIN_CAN_TX GPIO_NUM_47
#define PIN_CAN_RX GPIO_NUM_38
#define PIN_CAN_nSILENT GPIO_NUM_1

#define PIN_UART_TX 18
#define PIN_UART_RX 17

#define WS2812_LED_PIN GPIO_NUM_33

#define PIN_CAN_TERM GPIO_NUM_11
#define CAN_TERM_EN  LOW

#define CAN_APP_NODE_NAME "vk-rid"
#else
#error "unsupported board"
#endif