V9_PMU302_Bootloader/Drivers/STM32F3xx_HAL_Driver/Src/stm32f3xx_hal_sdadc.c

/**
  ******************************************************************************
  * @file    stm32f3xx_hal_sdadc.c
  * @author  MCD Application Team
  * @brief   This file provides firmware functions to manage the following
  *          functionalities of the Sigma-Delta Analog to Digital Converter
  *          (SDADC) peripherals:
  *           + Initialization and Configuration
  *           + Regular Channels Configuration
  *           + Injected channels Configuration
  *           + Power saving
  *           + Regular/Injected Channels DMA Configuration
  *           + Interrupts and flags management
  ******************************************************************************
  * @attention
  *
  * Copyright (c) 2016 STMicroelectronics.
  * All rights reserved.
  *
  * This software is licensed under terms that can be found in the LICENSE file
  * in the root directory of this software component.
  * If no LICENSE file comes with this software, it is provided AS-IS.
  *
  ******************************************************************************
  @verbatim
  ==============================================================================
                    ##### SDADC specific features #####
  ==============================================================================
  [..]
  (#) 16-bit sigma delta architecture.
  (#) Self calibration.
  (#) Interrupt generation at the end of calibration, regular/injected conversion
      and in case of overrun events.
  (#) Single and continuous conversion modes.
  (#) External trigger option with configurable polarity for injected conversion.
  (#) Multi mode (synchronized another SDADC with SDADC1).
  (#) DMA request generation during regular or injected channel conversion.

                     ##### How to use this driver #####
  ==============================================================================
  [..]
    *** Initialization ***
    ======================
    [..]
      (#) As prerequisite, fill in the HAL_SDADC_MspInit() :
        (++) Enable SDADCx clock interface with __SDADCx_CLK_ENABLE().
        (++) Configure SDADCx clock divider with HAL_RCCEx_PeriphCLKConfig.
        (++) Enable power on SDADC with HAL_PWREx_EnableSDADC().
        (++) Enable the clocks for the SDADC GPIOS with __HAL_RCC_GPIOx_CLK_ENABLE().
        (++) Configure these SDADC pins in analog mode using HAL_GPIO_Init().
        (++) If interrupt mode is used, enable and configure SDADC global
            interrupt with HAL_NVIC_SetPriority() and HAL_NVIC_EnableIRQ().
        (++) If DMA mode is used, configure DMA with HAL_DMA_Init and link it
            with SDADC handle using __HAL_LINKDMA.
      (#) Configure the SDADC low power mode, fast conversion mode, slow clock
          mode and SDADC1 reference voltage using the HAL_SDADC_Init() function.
          Note: Common reference voltage. is common to all SDADC instances.
      (#) Prepare channel configurations (input mode, common mode, gain and
          offset) using HAL_SDADC_PrepareChannelConfig and associate channel
          with one configuration using HAL_SDADC_AssociateChannelConfig.

    *** Calibration ***
    ============================================
    [..]
      (#) Start calibration using HAL_SDADC_StartCalibration or
          HAL_SDADC_CalibrationStart_IT.
      (#) In polling mode, use HAL_SDADC_PollForCalibEvent to detect the end of
          calibration.
      (#) In interrupt mode, HAL_SDADC_CalibrationCpltCallback will be called at
          the end of calibration.

    *** Regular channel conversion ***
    ============================================
    [..]
      (#) Select trigger for regular conversion using
          HAL_SDADC_SelectRegularTrigger.
      (#) Select regular channel and enable/disable continuous mode using
          HAL_SDADC_ConfigChannel.
      (#) Start regular conversion using HAL_SDADC_Start, HAL_SDADC_Start_IT
          or HAL_SDADC_Start_DMA.
      (#) In polling mode, use HAL_SDADC_PollForConversion to detect the end of
          regular conversion.
      (#) In interrupt mode, HAL_SDADC_ConvCpltCallback will be called at the
          end of regular conversion.
      (#) Get value of regular conversion using HAL_SDADC_GetValue.
      (#) In DMA mode, HAL_SDADC_ConvHalfCpltCallback and
          HAL_SDADC_ConvCpltCallback will be called respectively at the half
          transfer and at the transfer complete.
      (#) Stop regular conversion using HAL_SDADC_Stop, HAL_SDADC_Stop_IT
          or HAL_SDADC_Stop_DMA.

    *** Injected channels conversion ***
    ============================================
    [..]
      (#) Enable/disable delay on injected conversion using
          HAL_SDADC_SelectInjectedDelay.
      (#) If external trigger is used for injected conversion, configure this
          trigger using HAL_SDADC_SelectInjectedExtTrigger.
      (#) Select trigger for injected conversion using
          HAL_SDADC_SelectInjectedTrigger.
      (#) Select injected channels and enable/disable continuous mode using
          HAL_SDADC_InjectedConfigChannel.
      (#) Start injected conversion using HAL_SDADC_InjectedStart,
          HAL_SDADC_InjectedStart_IT or HAL_SDADC_InjectedStart_DMA.
      (#) In polling mode, use HAL_SDADC_PollForInjectedConversion to detect the
          end of injected conversion.
      (#) In interrupt mode, HAL_SDADC_InjectedConvCpltCallback will be called
          at the end of injected conversion.
      (#) Get value of injected conversion and corresponding channel using
          HAL_SDADC_InjectedGetValue.
      (#) In DMA mode, HAL_SDADC_InjectedConvHalfCpltCallback and
          HAL_SDADC_InjectedConvCpltCallback will be called respectively at the
          half transfer and at the transfer complete.
      (#) Stop injected conversion using HAL_SDADC_InjectedStop,
          HAL_SDADC_InjectedStop_IT or HAL_SDADC_InjectedStop_DMA.

    *** Multi mode regular channels conversions ***
    ======================================================
    [..]
      (#) Select type of multimode (SDADC1/SDADC2 or SDADC1/SDADC3) using
          HAL_SDADC_MultiModeConfigChannel.
      (#) Select software trigger for SDADC1 and synchronized trigger for
          SDADC2 (or SDADC3) using HAL_SDADC_SelectRegularTrigger.
      (#) Select regular channel for SDADC1 and SDADC2 (or SDADC3) using
          HAL_SDADC_ConfigChannel.
      (#) Start regular conversion for SDADC2 (or SDADC3) with HAL_SDADC_Start.
      (#) Start regular conversion for SDADC1 using HAL_SDADC_Start,
          HAL_SDADC_Start_IT or HAL_SDADC_MultiModeStart_DMA.
      (#) In polling mode, use HAL_SDADC_PollForConversion to detect the end of
          regular conversion for SDADC1.
      (#) In interrupt mode, HAL_SDADC_ConvCpltCallback will be called at the
          end of regular conversion for SDADC1.
      (#) Get value of regular conversions using HAL_SDADC_MultiModeGetValue.
      (#) In DMA mode, HAL_SDADC_ConvHalfCpltCallback and
          HAL_SDADC_ConvCpltCallback will be called respectively at the half
          transfer and at the transfer complete for SDADC1.
      (#) Stop regular conversion using HAL_SDADC_Stop, HAL_SDADC_Stop_IT
          or HAL_SDADC_MultiModeStop_DMA for SDADC1.
      (#) Stop regular conversion using HAL_SDADC_Stop for SDADC2 (or SDADC3).

    *** Multi mode injected channels conversions ***
    ======================================================
    [..]
      (#) Select type of multimode (SDADC1/SDADC2 or SDADC1/SDADC3) using
          HAL_SDADC_InjectedMultiModeConfigChannel.
      (#) Select software or external trigger for SDADC1 and synchronized
          trigger for SDADC2 (or SDADC3) using HAL_SDADC_SelectInjectedTrigger.
      (#) Select injected channels for SDADC1 and SDADC2 (or SDADC3) using
          HAL_SDADC_InjectedConfigChannel.
      (#) Start injected conversion for SDADC2 (or SDADC3) with
          HAL_SDADC_InjectedStart.
      (#) Start injected conversion for SDADC1 using HAL_SDADC_InjectedStart,
          HAL_SDADC_InjectedStart_IT or HAL_SDADC_InjectedMultiModeStart_DMA.
      (#) In polling mode, use HAL_SDADC_InjectedPollForConversion to detect
          the end of injected conversion for SDADC1.
      (#) In interrupt mode, HAL_SDADC_InjectedConvCpltCallback will be called
          at the end of injected conversion for SDADC1.
      (#) Get value of injected conversions using
          HAL_SDADC_InjectedMultiModeGetValue.
      (#) In DMA mode, HAL_SDADC_InjectedConvHalfCpltCallback and
          HAL_SDADC_InjectedConvCpltCallback will be called respectively at the
          half transfer and at the transfer complete for SDADC1.
      (#) Stop injected conversion using HAL_SDADC_InjectedStop,
          HAL_SDADC_InjectedStop_IT or HAL_SDADC_InjecteddMultiModeStop_DMA
          for SDADC1.
      (#) Stop injected conversion using HAL_SDADC_InjectedStop for SDADC2
          (or SDADC3).

    *** Callback registration ***
    =============================================
    [..]

     The compilation flag USE_HAL_SDADC_REGISTER_CALLBACKS, when set to 1,
     allows the user to configure dynamically the driver callbacks.
     Use Functions HAL_SDADC_RegisterCallback()
     to register an interrupt callback.
    [..]

     Function HAL_SDADC_RegisterCallback() allows to register following callbacks:
       (+) ConvHalfCpltCallback : callback for half regular conversion complete.
       (+) ConvCpltCallback : callback for regular conversion complete
       (+) InjectedConvHalfCpltCallback : callback for half injected conversion complete
       (+) InjectedConvCpltCallback : callback for injected conversion complete
       (+) CalibrationCpltCallback : callback for calibration
       (+) ErrorCallback : callback for error detection.
       (+) MspInitCallback : callback for Msp Init.
       (+) MspDeInitCallback : callback for Msp DeInit.
     This function takes as parameters the HAL peripheral handle, the Callback ID
     and a pointer to the user callback function.
    [..]

     Use function HAL_SDADC_UnRegisterCallback to reset a callback to the default
     weak function.
    [..]

     HAL_SDADC_UnRegisterCallback takes as parameters the HAL peripheral handle,
     and the Callback ID.
     This function allows to reset following callbacks:
       (+) ConvHalfCpltCallback : callback for half regular conversion complete.
       (+) ConvCpltCallback : callback for regular conversion complete
       (+) InjectedConvHalfCpltCallback : callback for half injected conversion complete
       (+) InjectedConvCpltCallback : callback for injected conversion complete
       (+) CalibrationCpltCallback : callback for calibration
       (+) ErrorCallback : callback for error detection.
       (+) MspInitCallback : callback for Msp Init.
       (+) MspDeInitCallback : callback for Msp DeInit.
     [..]

     By default, after the HAL_SDADC_Init() and when the state is HAL_SDADC_STATE_RESET
     all callbacks are set to the corresponding weak functions:
     examples HAL_SDADC_ConvCpltCallback(), HAL_SDADC_ErrorCallback().
     Exception done for MspInit and MspDeInit functions that are
     reset to the legacy weak functions in the HAL_SDADC_Init()/ HAL_SDADC_DeInit() only when
     these callbacks are null (not registered beforehand).
    [..]

     If MspInit or MspDeInit are not null, the HAL_SDADC_Init()/ HAL_SDADC_DeInit()
     keep and use the user MspInit/MspDeInit callbacks (registered beforehand) whatever the state.
     [..]

     Callbacks can be registered/unregistered in HAL_SDADC_STATE_READY state only.
     Exception done MspInit/MspDeInit functions that can be registered/unregistered
     in HAL_SDADC_STATE_READY or HAL_SDADC_STATE_RESET state,
     thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit.
    [..]

     Then, the user first registers the MspInit/MspDeInit user callbacks
     using HAL_SDADC_RegisterCallback() before calling HAL_SDADC_DeInit()
     or HAL_SDADC_Init() function.
     [..]

     When the compilation flag USE_HAL_SDADC_REGISTER_CALLBACKS is set to 0 or
     not defined, the callback registration feature is not available and all callbacks
     are set to the corresponding weak functions.

    @endverbatim
  */

/* Includes ------------------------------------------------------------------*/
#include "stm32f3xx_hal.h"

/** @addtogroup STM32F3xx_HAL_Driver
  * @{
  */

#ifdef HAL_SDADC_MODULE_ENABLED
#if defined(SDADC1) || defined(SDADC2) || defined(SDADC3)
/** @defgroup SDADC SDADC
  * @brief SDADC HAL driver modules
  * @{
  */

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/** @defgroup SDADC_Private_Define SDADC Private Define
 * @{
 */
#define SDADC_TIMEOUT          200UL
#define SDADC_CONFREG_OFFSET   0x00000020UL
#define SDADC_JDATAR_CH_OFFSET 24UL
#define SDADC_MSB_MASK         0xFFFF0000UL
#define SDADC_LSB_MASK         0x0000FFFFUL
/**
  * @}
  */

/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/** @defgroup SDADC_Private_Functions SDADC Private Functions
  * @{
  */

static HAL_StatusTypeDef SDADC_EnterInitMode(SDADC_HandleTypeDef* hsdadc);
static void              SDADC_ExitInitMode(SDADC_HandleTypeDef* hsdadc);
static uint32_t          SDADC_GetInjChannelsNbr(uint32_t Channels);
static HAL_StatusTypeDef SDADC_RegConvStart(SDADC_HandleTypeDef* hsdadc);
static HAL_StatusTypeDef SDADC_RegConvStop(SDADC_HandleTypeDef* hsdadc);
static HAL_StatusTypeDef SDADC_InjConvStart(SDADC_HandleTypeDef* hsdadc);
static HAL_StatusTypeDef SDADC_InjConvStop(SDADC_HandleTypeDef* hsdadc);
static void              SDADC_DMARegularHalfConvCplt(DMA_HandleTypeDef *hdma);
static void              SDADC_DMARegularConvCplt(DMA_HandleTypeDef *hdma);
static void              SDADC_DMAInjectedHalfConvCplt(DMA_HandleTypeDef *hdma);
static void              SDADC_DMAInjectedConvCplt(DMA_HandleTypeDef *hdma);
static void              SDADC_DMAError(DMA_HandleTypeDef *hdma);
/**
  * @}
  */

/* Exported functions ---------------------------------------------------------*/

/** @defgroup SDADC_Exported_Functions SDADC Exported Functions
  * @{
  */

/** @defgroup SDADC_Exported_Functions_Group1 Initialization and de-initialization functions
 *  @brief    Initialization and de-initialization functions
 *
@verbatim
  ===============================================================================
              ##### Initialization and de-initialization functions #####
  ===============================================================================
    [..]  This section provides functions allowing to:
      (+) Initialize the SDADC.
      (+) De-initialize the SDADC.

@endverbatim
  * @{
  */

/**
  * @brief  Initializes the SDADC according to the specified
  *         parameters in the SDADC_InitTypeDef structure.
  * @note   If multiple SDADC are used, please configure first SDADC1 to set
  *         the common reference voltage.
  * @param  hsdadc SDADC handle.
  * @retval HAL status.
  */
HAL_StatusTypeDef HAL_SDADC_Init(SDADC_HandleTypeDef* hsdadc)
{
  uint32_t tickstart;

  /* Check SDADC handle */
  if(hsdadc == NULL)
  {
    return HAL_ERROR;
  }

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(IS_SDADC_LOWPOWER_MODE(hsdadc->Init.IdleLowPowerMode));
  assert_param(IS_SDADC_FAST_CONV_MODE(hsdadc->Init.FastConversionMode));
  assert_param(IS_SDADC_SLOW_CLOCK_MODE(hsdadc->Init.SlowClockMode));
  assert_param(IS_SDADC_VREF(hsdadc->Init.ReferenceVoltage));

  /* Initialize SDADC variables with default values */
  hsdadc->RegularContMode     = SDADC_CONTINUOUS_CONV_OFF;
  hsdadc->InjectedContMode    = SDADC_CONTINUOUS_CONV_OFF;
  hsdadc->InjectedChannelsNbr = 1U;
  hsdadc->InjConvRemaining    = 1U;
  hsdadc->RegularTrigger      = SDADC_SOFTWARE_TRIGGER;
  hsdadc->InjectedTrigger     = SDADC_SOFTWARE_TRIGGER;
  hsdadc->ExtTriggerEdge      = SDADC_EXT_TRIG_RISING_EDGE;
  hsdadc->RegularMultimode    = SDADC_MULTIMODE_SDADC1_SDADC2;
  hsdadc->InjectedMultimode   = SDADC_MULTIMODE_SDADC1_SDADC2;
  hsdadc->ErrorCode           = SDADC_ERROR_NONE;

#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
  if(hsdadc->State == HAL_SDADC_STATE_RESET)
  {
    /* Init the SDADC Callback settings */
    hsdadc->ConvHalfCpltCallback         = HAL_SDADC_ConvHalfCpltCallback;
    hsdadc->ConvCpltCallback             = HAL_SDADC_ConvCpltCallback;
    hsdadc->InjectedConvHalfCpltCallback = HAL_SDADC_InjectedConvHalfCpltCallback;
    hsdadc->InjectedConvCpltCallback     = HAL_SDADC_InjectedConvCpltCallback;
    hsdadc->CalibrationCpltCallback      = HAL_SDADC_CalibrationCpltCallback;
    hsdadc->ErrorCallback                = HAL_SDADC_ErrorCallback;
  }

  if (hsdadc->MspInitCallback == NULL)
  {
    hsdadc->MspInitCallback = HAL_SDADC_MspInit; /* Legacy weak MspInit  */
  }

  /* Init the low level hardware */
  hsdadc->MspInitCallback(hsdadc);
#else
  /* Init the low level hardware */
  HAL_SDADC_MspInit(hsdadc);
#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */

  /* Set idle low power and slow clock modes */
  hsdadc->Instance->CR1 &= ~(SDADC_CR1_SBI|SDADC_CR1_PDI|SDADC_CR1_SLOWCK);
  hsdadc->Instance->CR1 |= (hsdadc->Init.IdleLowPowerMode | \
                            hsdadc->Init.SlowClockMode);

  /* Set fast conversion mode */
  hsdadc->Instance->CR2 &= ~(SDADC_CR2_FAST);
  hsdadc->Instance->CR2 |= hsdadc->Init.FastConversionMode;

  /* Set reference voltage common to all SDADC instances */
  /* Update this parameter only if needed to avoid unnecessary settling time */
  if((SDADC1->CR1 & SDADC_CR1_REFV) != hsdadc->Init.ReferenceVoltage)
  {
    /* Voltage reference bits are common to all SADC instances but are        */
    /* present in SDADC1 register.                                            */
    SDADC1->CR1 &= ~(SDADC_CR1_REFV);
    SDADC1->CR1 |= hsdadc->Init.ReferenceVoltage;

    /* Wait at least 2ms before setting ADON */
    HAL_Delay(2U);
  }

  /* Enable SDADC */
  hsdadc->Instance->CR2 |= SDADC_CR2_ADON;

  /* Wait end of stabilization */
  tickstart = HAL_GetTick();
  while((hsdadc->Instance->ISR & SDADC_ISR_STABIP) != 0UL)
  {
    if((HAL_GetTick()-tickstart) > SDADC_TIMEOUT)
    {
      return HAL_TIMEOUT;
    }
  }

  /* Set SDADC to ready state */
  hsdadc->State = HAL_SDADC_STATE_READY;

  /* Return HAL status */
  return HAL_OK;
}

/**
  * @brief  De-initializes the SDADC.
  * @param  hsdadc SDADC handle.
  * @retval HAL status.
  */
HAL_StatusTypeDef HAL_SDADC_DeInit(SDADC_HandleTypeDef* hsdadc)
{
  /* Check SDADC handle */
  if(hsdadc == NULL)
  {
    return HAL_ERROR;
  }

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Disable the SDADC */
  hsdadc->Instance->CR2 &= ~(SDADC_CR2_ADON);

  /* Reset all registers */
  hsdadc->Instance->CR1      = 0x00000000UL;
  hsdadc->Instance->CR2      = 0x00000000UL;
  hsdadc->Instance->JCHGR    = 0x00000001UL;
  hsdadc->Instance->CONF0R   = 0x00000000UL;
  hsdadc->Instance->CONF1R   = 0x00000000UL;
  hsdadc->Instance->CONF2R   = 0x00000000UL;
  hsdadc->Instance->CONFCHR1 = 0x00000000UL;
  hsdadc->Instance->CONFCHR2 = 0x00000000UL;

#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
    if (hsdadc->MspDeInitCallback == NULL)
    {
      hsdadc->MspDeInitCallback = HAL_SDADC_MspDeInit; /* Legacy weak MspDeInit */
    }

    /* DeInit the low level hardware */
    hsdadc->MspDeInitCallback(hsdadc);
#else
    /* DeInit the low level hardware */
    HAL_SDADC_MspDeInit(hsdadc);
#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */

  /* Set SDADC in reset state */
  hsdadc->State = HAL_SDADC_STATE_RESET;

  /* Return function status */
  return HAL_OK;
}

/**
  * @brief  Initializes the SDADC MSP.
  * @param  hsdadc SDADC handle
  * @retval None
  */
__weak void HAL_SDADC_MspInit(SDADC_HandleTypeDef* hsdadc)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hsdadc);

  /* NOTE : This function should not be modified, when the callback is needed,
            the HAL_SDADC_MspInit could be implemented in the user file.
   */
}

/**
  * @brief  De-initializes the SDADC MSP.
  * @param  hsdadc SDADC handle
  * @retval None
  */
__weak void HAL_SDADC_MspDeInit(SDADC_HandleTypeDef* hsdadc)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hsdadc);

  /* NOTE : This function should not be modified, when the callback is needed,
            the HAL_SDADC_MspDeInit could be implemented in the user file.
   */
}
#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
/**
  * @brief  Register a User SDADC Callback
  *         To be used instead of the weak predefined callback
  * @param  hsdadc Pointer to a SDADC_HandleTypeDef structure that contains
  *                the configuration information for the specified SDADC.
  * @param  CallbackID ID of the callback to be registered
  *         This parameter can be one of the following values:
  *          @arg @ref HAL_SDADC_CONVERSION_HALF_CB_ID          SDADC half regular conversion complete callback ID
  *          @arg @ref HAL_SDADC_CONVERSION_COMPLETE_CB_ID      SDADC regular conversion complete callback ID
  *          @arg @ref HAL_SDADC_INJ_CONVERSION_HALF_CB_ID      SDADC half injected conversion complete callback ID
  *          @arg @ref HAL_SDADC_INJ_CONVERSION_COMPLETE_CB_ID  SDADC injected conversion complete callback ID
  *          @arg @ref HAL_SDADC_CALIBRATION_COMPLETE_CB_ID     SDADC calibration callback ID
  *          @arg @ref HAL_SDADC_ERROR_CB_ID                    SDADC error callback ID
  *          @arg @ref HAL_SDADC_MSPINIT_CB_ID                  SDADC Msp Init callback ID
  *          @arg @ref HAL_SDADC_MSPDEINIT_CB_ID                SDADC Msp DeInit callback ID
  * @param  pCallback pointer to the Callback function
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_RegisterCallback(SDADC_HandleTypeDef *hsdadc, HAL_SDADC_CallbackIDTypeDef CallbackID, pSDADC_CallbackTypeDef pCallback)
{
  HAL_StatusTypeDef status = HAL_OK;

  if (pCallback == NULL)
  {
    /* Update the error code */
    hsdadc->ErrorCode |= SDADC_ERROR_INVALID_CALLBACK;

    return HAL_ERROR;
  }

  if (HAL_SDADC_STATE_READY == hsdadc->State)
  {
    switch (CallbackID)
    {
      case HAL_SDADC_CONVERSION_HALF_CB_ID :
        hsdadc->ConvHalfCpltCallback = pCallback;
        break;

      case HAL_SDADC_CONVERSION_COMPLETE_CB_ID :
        hsdadc->ConvCpltCallback = pCallback;
        break;

      case HAL_SDADC_INJ_CONVERSION_HALF_CB_ID :
        hsdadc->InjectedConvHalfCpltCallback = pCallback;
        break;

      case HAL_SDADC_INJ_CONVERSION_COMPLETE_CB_ID :
        hsdadc->InjectedConvCpltCallback = pCallback;
        break;

      case HAL_SDADC_CALIBRATION_COMPLETE_CB_ID :
        hsdadc->CalibrationCpltCallback = pCallback;
        break;

      case HAL_SDADC_ERROR_CB_ID :
        hsdadc->ErrorCallback = pCallback;
        break;

      case HAL_SDADC_MSPINIT_CB_ID :
        hsdadc->MspInitCallback = pCallback;
        break;

      case HAL_SDADC_MSPDEINIT_CB_ID :
        hsdadc->MspDeInitCallback = pCallback;
        break;

      default :
        /* Update the error code */
        hsdadc->ErrorCode |= SDADC_ERROR_INVALID_CALLBACK;

        /* Return error status */
        status = HAL_ERROR;
        break;
    }
  }
  else if (HAL_SDADC_STATE_RESET == hsdadc->State)
  {
    switch (CallbackID)
    {
      case HAL_SDADC_MSPINIT_CB_ID :
        hsdadc->MspInitCallback = pCallback;
        break;

      case HAL_SDADC_MSPDEINIT_CB_ID :
        hsdadc->MspDeInitCallback = pCallback;
        break;

      default :
        /* Update the error code */
        hsdadc->ErrorCode |= SDADC_ERROR_INVALID_CALLBACK;

        /* Return error status */
        status = HAL_ERROR;
        break;
    }
  }
  else
  {
    /* Update the error code */
    hsdadc->ErrorCode |= SDADC_ERROR_INVALID_CALLBACK;

    /* Return error status */
    status =  HAL_ERROR;
  }

  return status;
}

/**
  * @brief  Unregister a SDADC Callback
  *         ADC callback is redirected to the weak predefined callback
  * @param  hsdadc Pointer to a SDADC_HandleTypeDef structure that contains
  *                the configuration information for the specified ADC.
  * @param  CallbackID ID of the callback to be unregistered
  *         This parameter can be one of the following values:
  *          @arg @ref HAL_SDADC_CONVERSION_HALF_CB_ID          SDADC half regular conversion complete callback ID
  *          @arg @ref HAL_SDADC_CONVERSION_COMPLETE_CB_ID      SDADC regular conversion complete callback ID
  *          @arg @ref HAL_SDADC_INJ_CONVERSION_HALF_CB_ID      SDADC half injected conversion complete callback ID
  *          @arg @ref HAL_SDADC_INJ_CONVERSION_COMPLETE_CB_ID  SDADC injected conversion complete callback ID
  *          @arg @ref HAL_SDADC_CALIBRATION_COMPLETE_CB_ID     SDADC calibration callback ID
  *          @arg @ref HAL_SDADC_ERROR_CB_ID                    SDADC error callback ID
  *          @arg @ref HAL_SDADC_MSPINIT_CB_ID                  SDADC Msp Init callback ID
  *          @arg @ref HAL_SDADC_MSPDEINIT_CB_ID                SDADC Msp DeInit callback ID
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_UnRegisterCallback(SDADC_HandleTypeDef *hsdadc, HAL_SDADC_CallbackIDTypeDef CallbackID)
{
  HAL_StatusTypeDef status = HAL_OK;

  if (HAL_SDADC_STATE_READY == hsdadc->State)
  {
    switch (CallbackID)
    {
      case HAL_SDADC_CONVERSION_HALF_CB_ID :
        hsdadc->ConvHalfCpltCallback = HAL_SDADC_ConvHalfCpltCallback;
        break;

      case HAL_SDADC_CONVERSION_COMPLETE_CB_ID :
        hsdadc->ConvCpltCallback = HAL_SDADC_ConvCpltCallback;
        break;

      case HAL_SDADC_INJ_CONVERSION_HALF_CB_ID :
        hsdadc->InjectedConvHalfCpltCallback = HAL_SDADC_InjectedConvHalfCpltCallback;
        break;

      case HAL_SDADC_INJ_CONVERSION_COMPLETE_CB_ID :
        hsdadc->InjectedConvCpltCallback = HAL_SDADC_InjectedConvCpltCallback;
        break;

      case HAL_SDADC_CALIBRATION_COMPLETE_CB_ID :
        hsdadc->CalibrationCpltCallback = HAL_SDADC_CalibrationCpltCallback;
        break;

      case HAL_SDADC_ERROR_CB_ID :
        hsdadc->ErrorCallback = HAL_SDADC_ErrorCallback;
        break;

      case HAL_SDADC_MSPINIT_CB_ID :
        hsdadc->MspInitCallback = HAL_SDADC_MspInit;
        break;

      case HAL_SDADC_MSPDEINIT_CB_ID :
        hsdadc->MspDeInitCallback = HAL_SDADC_MspDeInit;
        break;

      default :
        /* Update the error code */
        hsdadc->ErrorCode |= SDADC_ERROR_INVALID_CALLBACK;

        /* Return error status */
        status =  HAL_ERROR;
        break;
    }
  }
  else if (HAL_SDADC_STATE_RESET == hsdadc->State)
  {
    switch (CallbackID)
    {
      case HAL_SDADC_MSPINIT_CB_ID :
        hsdadc->MspInitCallback = HAL_SDADC_MspInit;                   /* Legacy weak MspInit              */
        break;

      case HAL_SDADC_MSPDEINIT_CB_ID :
        hsdadc->MspDeInitCallback = HAL_SDADC_MspDeInit;               /* Legacy weak MspDeInit            */
        break;

      default :
        /* Update the error code */
        hsdadc->ErrorCode |= SDADC_ERROR_INVALID_CALLBACK;

        /* Return error status */
        status =  HAL_ERROR;
        break;
    }
  }
  else
  {
    /* Update the error code */
    hsdadc->ErrorCode |= SDADC_ERROR_INVALID_CALLBACK;

    /* Return error status */
    status =  HAL_ERROR;
  }

  return status;
}

#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */

/**
  * @}
  */

/** @defgroup SDADC_Exported_Functions_Group2 peripheral control functions
 *  @brief    Peripheral control functions
 *
@verbatim
  ===============================================================================
              ##### Peripheral control functions #####
  ===============================================================================
    [..]  This section provides functions allowing to:
      (+) Program one of the three different configurations for channels.
      (+) Associate channel to one of configurations.
      (+) Select regular and injected channels.
      (+) Enable/disable continuous mode for regular and injected conversions.
      (+) Select regular and injected triggers.
      (+) Select and configure injected external trigger.
      (+) Enable/disable delay addition for injected conversions.
      (+) Configure multimode.

@endverbatim
  * @{
  */

/**
  * @brief  This function allows the user to set parameters for a configuration.
  *         Parameters are input mode, common mode, gain and offset.
  * @note   This function should be called only when SDADC instance is in idle state
  *         (neither calibration nor regular or injected conversion ongoing)
  * @param  hsdadc SDADC handle.
  * @param  ConfIndex Index of configuration to modify.
  *         This parameter can be a value of @ref SDADC_ConfIndex.
  * @param  ConfParamStruct Parameters to apply for this configuration.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_PrepareChannelConfig(SDADC_HandleTypeDef *hsdadc,
                                                 uint32_t ConfIndex,
                                                 SDADC_ConfParamTypeDef* ConfParamStruct)
{
  HAL_StatusTypeDef status = HAL_OK;
  uint32_t          tmp;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(IS_SDADC_CONF_INDEX(ConfIndex));
  assert_param(ConfParamStruct != ((void*) 0));
  assert_param(IS_SDADC_INPUT_MODE(ConfParamStruct->InputMode));
  assert_param(IS_SDADC_GAIN(ConfParamStruct->Gain));
  assert_param(IS_SDADC_COMMON_MODE(ConfParamStruct->CommonMode));
  assert_param(IS_SDADC_OFFSET_VALUE(ConfParamStruct->Offset));

  /* Check SDADC state is ready */
  if(hsdadc->State != HAL_SDADC_STATE_READY)
  {
    status = HAL_ERROR;
  }
  else
  {
    /* Enter init mode */
    if(SDADC_EnterInitMode(hsdadc) != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_TIMEOUT;
    }
    else
    {
      /* Program configuration register with parameters */
      tmp = (uint32_t)((uint32_t)(hsdadc->Instance) + \
                       SDADC_CONFREG_OFFSET + \
                       (uint32_t)(ConfIndex << 2UL));
      *(__IO uint32_t *) (tmp) = (uint32_t) (ConfParamStruct->InputMode | \
                                             ConfParamStruct->Gain | \
                                             ConfParamStruct->CommonMode | \
                                             ConfParamStruct->Offset);
      /* Exit init mode */
      SDADC_ExitInitMode(hsdadc);
    }
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows the user to associate a channel with one of the
  *         available configurations.
  * @note   This function should be called only when SDADC instance is in idle state
  *         (neither calibration nor regular or injected conversion ongoing)
  * @param  hsdadc SDADC handle.
  * @param  Channel Channel to associate with configuration.
  *         This parameter can be a value of @ref SDADC_Channel_Selection.
  * @param  ConfIndex Index of configuration to associate with channel.
  *         This parameter can be a value of @ref SDADC_ConfIndex.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_AssociateChannelConfig(SDADC_HandleTypeDef *hsdadc,
                                                   uint32_t Channel,
                                                   uint32_t ConfIndex)
{
  HAL_StatusTypeDef status = HAL_OK;
  uint32_t          channelnum;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(IS_SDADC_REGULAR_CHANNEL(Channel));
  assert_param(IS_SDADC_CONF_INDEX(ConfIndex));

  /* Check SDADC state is ready */
  if(hsdadc->State != HAL_SDADC_STATE_READY)
  {
    status = HAL_ERROR;
  }
  else
  {
    /* Enter init mode */
    if(SDADC_EnterInitMode(hsdadc) != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_TIMEOUT;
    }
    else
    {
      /* Program channel configuration register according parameters */
      if(Channel != SDADC_CHANNEL_8)
      {
        /* Get channel number */
        channelnum = (uint32_t)(Channel>>16UL);

        /* Set the channel configuration */
        hsdadc->Instance->CONFCHR1 &= (uint32_t) ~((uint32_t)SDADC_CONFCHR1_CONFCH0 << ((channelnum << 2UL) & 0x1FUL));
        hsdadc->Instance->CONFCHR1 |= (uint32_t) (ConfIndex << ((channelnum << 2UL) & 0x1FUL));
      }
      else
      {
        hsdadc->Instance->CONFCHR2 = (uint32_t) (ConfIndex);
      }
      /* Exit init mode */
      SDADC_ExitInitMode(hsdadc);
    }
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to select channel for regular conversion and
  *         to enable/disable continuous mode for regular conversion.
  * @param  hsdadc SDADC handle.
  * @param  Channel Channel for regular conversion.
  *         This parameter can be a value of @ref SDADC_Channel_Selection.
  * @param  ContinuousMode Enable/disable continuous mode for regular conversion.
  *         This parameter can be a value of @ref SDADC_ContinuousMode.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_ConfigChannel(SDADC_HandleTypeDef *hsdadc,
                                          uint32_t Channel,
                                          uint32_t ContinuousMode)
{
  HAL_StatusTypeDef status = HAL_OK;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(IS_SDADC_REGULAR_CHANNEL(Channel));
  assert_param(IS_SDADC_CONTINUOUS_MODE(ContinuousMode));

  /* Check SDADC state */
  if((hsdadc->State != HAL_SDADC_STATE_RESET) && (hsdadc->State != HAL_SDADC_STATE_ERROR))
  {
    /* Set RCH[3:0] and RCONT bits in SDADC_CR2 */
    hsdadc->Instance->CR2 &= (uint32_t) ~(SDADC_CR2_RCH | SDADC_CR2_RCONT);
    if(ContinuousMode == SDADC_CONTINUOUS_CONV_ON)
    {
      hsdadc->Instance->CR2 |= (uint32_t) ((Channel & SDADC_MSB_MASK) | SDADC_CR2_RCONT);
    }
    else
    {
      hsdadc->Instance->CR2 |= (uint32_t) ((Channel & SDADC_MSB_MASK));
    }
    /* Store continuous mode information */
    hsdadc->RegularContMode = ContinuousMode;
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to select channels for injected conversion and
  *         to enable/disable continuous mode for injected conversion.
  * @param  hsdadc SDADC handle.
  * @param  Channel Channels for injected conversion.
  *         This parameter can be a values combination of @ref SDADC_Channel_Selection.
  * @param  ContinuousMode Enable/disable continuous mode for injected conversion.
  *         This parameter can be a value of @ref SDADC_ContinuousMode.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_InjectedConfigChannel(SDADC_HandleTypeDef *hsdadc,
                                                  uint32_t Channel,
                                                  uint32_t ContinuousMode)
{
  HAL_StatusTypeDef status = HAL_OK;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(IS_SDADC_INJECTED_CHANNEL(Channel));
  assert_param(IS_SDADC_CONTINUOUS_MODE(ContinuousMode));

  /* Check SDADC state */
  if((hsdadc->State != HAL_SDADC_STATE_RESET) && (hsdadc->State != HAL_SDADC_STATE_ERROR))
  {
    /* Set JCHG[8:0] bits in SDADC_JCHG */
    hsdadc->Instance->JCHGR = (uint32_t) (Channel & SDADC_LSB_MASK);
    /* Set or clear JCONT bit in SDADC_CR2 */
    if(ContinuousMode == SDADC_CONTINUOUS_CONV_ON)
    {
      hsdadc->Instance->CR2 |= SDADC_CR2_JCONT;
    }
    else
    {
      hsdadc->Instance->CR2 &= ~(SDADC_CR2_JCONT);
    }
    /* Store continuous mode information */
    hsdadc->InjectedContMode = ContinuousMode;
    /* Store number of injected channels */
    hsdadc->InjectedChannelsNbr = SDADC_GetInjChannelsNbr(Channel);
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to select trigger for regular conversions.
  * @note   This function should not be called if regular conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @param  Trigger Trigger for regular conversions.
  *         This parameter can be one of the following value :
  *            @arg SDADC_SOFTWARE_TRIGGER : Software trigger.
  *            @arg SDADC_SYNCHRONOUS_TRIGGER : Synchronous with SDADC1 (only for SDADC2 and SDADC3).
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_SelectRegularTrigger(SDADC_HandleTypeDef *hsdadc, uint32_t Trigger)
{
  HAL_StatusTypeDef status = HAL_OK;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(IS_SDADC_REGULAR_TRIGGER(Trigger));

  /* Check parameters compatibility */
  if((hsdadc->Instance == SDADC1) && (Trigger == SDADC_SYNCHRONOUS_TRIGGER))
  {
    status = HAL_ERROR;
  }
  /* Check SDADC state */
  else if((hsdadc->State == HAL_SDADC_STATE_READY) || \
          (hsdadc->State == HAL_SDADC_STATE_CALIB) || \
          (hsdadc->State == HAL_SDADC_STATE_INJ))
  {
    /* Store regular trigger information */
    hsdadc->RegularTrigger = Trigger;
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to select trigger for injected conversions.
  * @note   This function should not be called if injected conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @param  Trigger Trigger for injected conversions.
  *         This parameter can be one of the following value :
  *            @arg SDADC_SOFTWARE_TRIGGER : Software trigger.
  *            @arg SDADC_SYNCHRONOUS_TRIGGER : Synchronous with SDADC1 (only for SDADC2 and SDADC3).
  *            @arg SDADC_EXTERNAL_TRIGGER : External trigger.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_SelectInjectedTrigger(SDADC_HandleTypeDef *hsdadc, uint32_t Trigger)
{
  HAL_StatusTypeDef status = HAL_OK;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(IS_SDADC_INJECTED_TRIGGER(Trigger));

  /* Check parameters compatibility */
  if((hsdadc->Instance == SDADC1) && (Trigger == SDADC_SYNCHRONOUS_TRIGGER))
  {
    status = HAL_ERROR;
  }
  /* Check SDADC state */
  else if((hsdadc->State == HAL_SDADC_STATE_READY) || \
          (hsdadc->State == HAL_SDADC_STATE_CALIB) || \
          (hsdadc->State == HAL_SDADC_STATE_REG))
  {
    /* Store regular trigger information */
    hsdadc->InjectedTrigger = Trigger;
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to select and configure injected external trigger.
  * @note   This function should be called only when SDADC instance is in idle state
  *         (neither calibration nor regular or injected conversion ongoing)
  * @param  hsdadc SDADC handle.
  * @param  InjectedExtTrigger External trigger for injected conversions.
  *         This parameter can be a value of @ref SDADC_InjectedExtTrigger.
  * @param  ExtTriggerEdge Edge of external injected trigger.
  *         This parameter can be a value of @ref SDADC_ExtTriggerEdge.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_SelectInjectedExtTrigger(SDADC_HandleTypeDef *hsdadc,
                                                     uint32_t InjectedExtTrigger,
                                                     uint32_t ExtTriggerEdge)
{
  HAL_StatusTypeDef status = HAL_OK;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(IS_SDADC_EXT_INJEC_TRIG(InjectedExtTrigger));
  assert_param(IS_SDADC_EXT_TRIG_EDGE(ExtTriggerEdge));

  /* Check SDADC state */
  if(hsdadc->State == HAL_SDADC_STATE_READY)
  {
    /* Enter init mode */
    if(SDADC_EnterInitMode(hsdadc) != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_TIMEOUT;
    }
    else
    {
      /* Set JEXTSEL[2:0] bits in SDADC_CR2 register */
      hsdadc->Instance->CR2 &= ~(SDADC_CR2_JEXTSEL);
      hsdadc->Instance->CR2 |= InjectedExtTrigger;

      /* Store external trigger edge information */
      hsdadc->ExtTriggerEdge = ExtTriggerEdge;

      /* Exit init mode */
      SDADC_ExitInitMode(hsdadc);
    }
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to enable/disable delay addition for injected conversions.
  * @note   This function should be called only when SDADC instance is in idle state
  *         (neither calibration nor regular or injected conversion ongoing)
  * @param  hsdadc SDADC handle.
  * @param  InjectedDelay Enable/disable delay for injected conversions.
  *         This parameter can be a value of @ref SDADC_InjectedDelay.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_SelectInjectedDelay(SDADC_HandleTypeDef *hsdadc,
                                                uint32_t InjectedDelay)
{
  HAL_StatusTypeDef status = HAL_OK;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(IS_SDADC_INJECTED_DELAY(InjectedDelay));

  /* Check SDADC state */
  if(hsdadc->State == HAL_SDADC_STATE_READY)
  {
    /* Enter init mode */
    if(SDADC_EnterInitMode(hsdadc) != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_TIMEOUT;
    }
    else
    {
      /* Set JDS bit in SDADC_CR2 register */
      hsdadc->Instance->CR2 &= ~(SDADC_CR2_JDS);
      hsdadc->Instance->CR2 |= InjectedDelay;

      /* Exit init mode */
      SDADC_ExitInitMode(hsdadc);
    }
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to configure multimode for regular conversions.
  * @note   This function should not be called if regular conversion is ongoing
  *         and should be could only for SDADC1.
  * @param  hsdadc SDADC handle.
  * @param  MultimodeType Type of multimode for regular conversions.
  *         This parameter can be a value of @ref SDADC_MultimodeType.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_MultiModeConfigChannel(SDADC_HandleTypeDef* hsdadc,
                                                   uint32_t MultimodeType)
{
  HAL_StatusTypeDef status = HAL_OK;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(IS_SDADC_MULTIMODE_TYPE(MultimodeType));

  /* Check instance is SDADC1 */
  if(hsdadc->Instance != SDADC1)
  {
    status = HAL_ERROR;
  }
  /* Check SDADC state */
  else if((hsdadc->State == HAL_SDADC_STATE_READY) || \
          (hsdadc->State == HAL_SDADC_STATE_CALIB) || \
          (hsdadc->State == HAL_SDADC_STATE_INJ))
  {
    /* Store regular trigger information */
    hsdadc->RegularMultimode = MultimodeType;
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to configure multimode for injected conversions.
  * @note   This function should not be called if injected conversion is ongoing
  *         and should be could only for SDADC1.
  * @param  hsdadc SDADC handle.
  * @param  MultimodeType Type of multimode for injected conversions.
  *         This parameter can be a value of @ref SDADC_MultimodeType.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_InjectedMultiModeConfigChannel(SDADC_HandleTypeDef* hsdadc,
                                                           uint32_t MultimodeType)
{
  HAL_StatusTypeDef status = HAL_OK;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(IS_SDADC_MULTIMODE_TYPE(MultimodeType));

  /* Check instance is SDADC1 */
  if(hsdadc->Instance != SDADC1)
  {
    status = HAL_ERROR;
  }
  /* Check SDADC state */
  else if((hsdadc->State == HAL_SDADC_STATE_READY) || \
          (hsdadc->State == HAL_SDADC_STATE_CALIB) || \
          (hsdadc->State == HAL_SDADC_STATE_REG))
  {
    /* Store regular trigger information */
    hsdadc->InjectedMultimode = MultimodeType;
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @}
  */

/** @defgroup SDADC_Exported_Functions_Group3 Input and Output operation functions
 *  @brief    IO operation Control functions
 *
@verbatim
  ===============================================================================
              ##### IO operation functions #####
  ===============================================================================
    [..]  This section provides functions allowing to:
      (+) Start calibration.
      (+) Poll for the end of calibration.
      (+) Start calibration and enable interrupt.
      (+) Start conversion of regular/injected channel.
      (+) Poll for the end of regular/injected conversion.
      (+) Stop conversion of regular/injected channel.
      (+) Start conversion of regular/injected channel and enable interrupt.
      (+) Stop conversion of regular/injected channel and disable interrupt.
      (+) Start conversion of regular/injected channel and enable DMA transfer.
      (+) Stop conversion of regular/injected channel and disable DMA transfer.
      (+) Start multimode and enable DMA transfer for regular/injected conversion.
      (+) Stop multimode and disable DMA transfer for regular/injected conversion..
      (+) Get result of regular channel conversion.
      (+) Get result of injected channel conversion.
      (+) Get result of multimode conversion.
      (+) Handle SDADC interrupt request.
      (+) Callbacks for calibration and regular/injected conversions.

@endverbatim
  * @{
  */

/**
  * @brief  This function allows to start calibration in polling mode.
  * @note   This function should be called only when SDADC instance is in idle state
  *         (neither calibration nor regular or injected conversion ongoing).
  * @param  hsdadc SDADC handle.
  * @param  CalibrationSequence Calibration sequence.
  *         This parameter can be a value of @ref SDADC_CalibrationSequence.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_CalibrationStart(SDADC_HandleTypeDef *hsdadc,
                                             uint32_t CalibrationSequence)
{
  HAL_StatusTypeDef status = HAL_OK;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(IS_SDADC_CALIB_SEQUENCE(CalibrationSequence));

  /* Check SDADC state */
  if(hsdadc->State == HAL_SDADC_STATE_READY)
  {
    /* Enter init mode */
    if(SDADC_EnterInitMode(hsdadc) != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_TIMEOUT;
    }
    else
    {
      /* Set CALIBCNT[1:0] bits in SDADC_CR2 register */
      hsdadc->Instance->CR2 &= ~(SDADC_CR2_CALIBCNT);
      hsdadc->Instance->CR2 |= CalibrationSequence;

      /* Exit init mode */
      SDADC_ExitInitMode(hsdadc);

      /* Set STARTCALIB in SDADC_CR2 */
      hsdadc->Instance->CR2 |= SDADC_CR2_STARTCALIB;

      /* Set SDADC in calibration state */
      hsdadc->State = HAL_SDADC_STATE_CALIB;
    }
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to poll for the end of calibration.
  * @note   This function should be called only if calibration is ongoing.
  * @param  hsdadc SDADC handle.
  * @param  Timeout Timeout value in milliseconds.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_PollForCalibEvent(SDADC_HandleTypeDef* hsdadc, uint32_t Timeout)
{
  uint32_t tickstart;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check SDADC state */
  if(hsdadc->State != HAL_SDADC_STATE_CALIB)
  {
    /* Return error status */
    return HAL_ERROR;
  }
  else
  {
    /* Get timeout */
    tickstart = HAL_GetTick();

    /* Wait EOCALF bit in SDADC_ISR register */
    while((hsdadc->Instance->ISR & SDADC_ISR_EOCALF) != SDADC_ISR_EOCALF)
    {
      /* Check the Timeout */
      if(Timeout != HAL_MAX_DELAY)
      {
        if(((HAL_GetTick()-tickstart) > Timeout) || (Timeout == 0UL))
        {
          /* Return timeout status */
          return HAL_TIMEOUT;
        }
      }
    }
    /* Set CLREOCALF bit in SDADC_CLRISR register */
    hsdadc->Instance->CLRISR |= SDADC_ISR_CLREOCALF;

    /* Set SDADC in ready state */
    hsdadc->State = HAL_SDADC_STATE_READY;

    /* Return function status */
    return HAL_OK;
  }
}

/**
  * @brief  This function allows to start calibration in interrupt mode.
  * @note   This function should be called only when SDADC instance is in idle state
  *         (neither calibration nor regular or injected conversion ongoing).
  * @param  hsdadc SDADC handle.
  * @param  CalibrationSequence Calibration sequence.
  *         This parameter can be a value of @ref SDADC_CalibrationSequence.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_CalibrationStart_IT(SDADC_HandleTypeDef *hsdadc,
                                                uint32_t CalibrationSequence)
{
  HAL_StatusTypeDef status = HAL_OK;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(IS_SDADC_CALIB_SEQUENCE(CalibrationSequence));

  /* Check SDADC state */
  if(hsdadc->State == HAL_SDADC_STATE_READY)
  {
    /* Enter init mode */
    if(SDADC_EnterInitMode(hsdadc) != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_TIMEOUT;
    }
    else
    {
      /* Set CALIBCNT[1:0] bits in SDADC_CR2 register */
      hsdadc->Instance->CR2 &= ~(SDADC_CR2_CALIBCNT);
      hsdadc->Instance->CR2 |= CalibrationSequence;

      /* Exit init mode */
      SDADC_ExitInitMode(hsdadc);

      /* Set EOCALIE bit in SDADC_CR1 register */
      hsdadc->Instance->CR1 |= SDADC_CR1_EOCALIE;

      /* Set STARTCALIB in SDADC_CR2 */
      hsdadc->Instance->CR2 |= SDADC_CR2_STARTCALIB;

      /* Set SDADC in calibration state */
      hsdadc->State = HAL_SDADC_STATE_CALIB;
    }
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to start regular conversion in polling mode.
  * @note   This function should be called only when SDADC instance is in idle state
  *         or if injected conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_Start(SDADC_HandleTypeDef *hsdadc)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check SDADC state */
  if((hsdadc->State == HAL_SDADC_STATE_READY) || \
     (hsdadc->State == HAL_SDADC_STATE_INJ))
  {
    /* Start regular conversion */
    status = SDADC_RegConvStart(hsdadc);
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to poll for the end of regular conversion.
  * @note   This function should be called only if regular conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @param  Timeout Timeout value in milliseconds.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_PollForConversion(SDADC_HandleTypeDef* hsdadc, uint32_t Timeout)
{
  uint32_t tickstart;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check SDADC state */
  if((hsdadc->State != HAL_SDADC_STATE_REG) && \
     (hsdadc->State != HAL_SDADC_STATE_REG_INJ))
  {
    /* Return error status */
    return HAL_ERROR;
  }
  else
  {
    /* Get timeout */
    tickstart = HAL_GetTick();

    /* Wait REOCF bit in SDADC_ISR register */
    while((hsdadc->Instance->ISR & SDADC_ISR_REOCF) != SDADC_ISR_REOCF)
    {
      /* Check the Timeout */
      if(Timeout != HAL_MAX_DELAY)
      {
        if(((HAL_GetTick()-tickstart) > Timeout) || (Timeout == 0UL))
        {
          /* Return timeout status */
          return HAL_TIMEOUT;
        }
      }
    }
    /* Check if overrun occurs */
    if((hsdadc->Instance->ISR & SDADC_ISR_ROVRF) == SDADC_ISR_ROVRF)
    {
      /* Update error code and call error callback */
      hsdadc->ErrorCode = SDADC_ERROR_REGULAR_OVERRUN;
#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
      hsdadc->ErrorCallback(hsdadc);
#else
      HAL_SDADC_ErrorCallback(hsdadc);
#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */

      /* Set CLRROVRF bit in SDADC_CLRISR register */
      hsdadc->Instance->CLRISR |= SDADC_ISR_CLRROVRF;
    }
    /* Update SDADC state only if not continuous conversion and SW trigger */
    if((hsdadc->RegularContMode == SDADC_CONTINUOUS_CONV_OFF) && \
       (hsdadc->RegularTrigger == SDADC_SOFTWARE_TRIGGER))
    {
      hsdadc->State = (hsdadc->State == HAL_SDADC_STATE_REG) ? \
                      HAL_SDADC_STATE_READY : HAL_SDADC_STATE_INJ;
    }
    /* Return function status */
    return HAL_OK;
  }
}

/**
  * @brief  This function allows to stop regular conversion in polling mode.
  * @note   This function should be called only if regular conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_Stop(SDADC_HandleTypeDef *hsdadc)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check SDADC state */
  if((hsdadc->State != HAL_SDADC_STATE_REG) && \
     (hsdadc->State != HAL_SDADC_STATE_REG_INJ))
  {
    /* Return error status */
    status = HAL_ERROR;
  }
  else
  {
    /* Stop regular conversion */
    status = SDADC_RegConvStop(hsdadc);
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to start regular conversion in interrupt mode.
  * @note   This function should be called only when SDADC instance is in idle state
  *         or if injected conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_Start_IT(SDADC_HandleTypeDef *hsdadc)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check SDADC state */
  if((hsdadc->State == HAL_SDADC_STATE_READY) || \
     (hsdadc->State == HAL_SDADC_STATE_INJ))
  {
    /* Set REOCIE and ROVRIE bits in SDADC_CR1 register */
    hsdadc->Instance->CR1 |= (uint32_t) (SDADC_CR1_REOCIE | SDADC_CR1_ROVRIE);

    /* Start regular conversion */
    status = SDADC_RegConvStart(hsdadc);
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to stop regular conversion in interrupt mode.
  * @note   This function should be called only if regular conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_Stop_IT(SDADC_HandleTypeDef *hsdadc)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check SDADC state */
  if((hsdadc->State != HAL_SDADC_STATE_REG) && \
     (hsdadc->State != HAL_SDADC_STATE_REG_INJ))
  {
    /* Return error status */
    status = HAL_ERROR;
  }
  else
  {
    /* Clear REOCIE and ROVRIE bits in SDADC_CR1 register */
    hsdadc->Instance->CR1 &= (uint32_t) ~(SDADC_CR1_REOCIE | SDADC_CR1_ROVRIE);

    /* Stop regular conversion */
    status = SDADC_RegConvStop(hsdadc);
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to start regular conversion in DMA mode.
  * @note   This function should be called only when SDADC instance is in idle state
  *         or if injected conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @param  pData The destination buffer address.
  * @param  Length The length of data to be transferred from SDADC peripheral to memory.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_Start_DMA(SDADC_HandleTypeDef *hsdadc, uint32_t *pData,
                                      uint32_t Length)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(pData != ((void*) 0));
  assert_param(Length != 0UL);

  /* Check that DMA is not enabled for injected conversion */
  if((hsdadc->Instance->CR1 & SDADC_CR1_JDMAEN) == SDADC_CR1_JDMAEN)
  {
    status = HAL_ERROR;
  }
  /* Check parameters compatibility */
  else if((hsdadc->RegularTrigger == SDADC_SOFTWARE_TRIGGER) && \
          (hsdadc->RegularContMode == SDADC_CONTINUOUS_CONV_OFF) && \
          (hsdadc->hdma->Init.Mode == DMA_NORMAL) && \
          (Length != 1U))
  {
    status = HAL_ERROR;
  }
  else if((hsdadc->RegularTrigger == SDADC_SOFTWARE_TRIGGER) && \
          (hsdadc->RegularContMode == SDADC_CONTINUOUS_CONV_OFF) && \
          (hsdadc->hdma->Init.Mode == DMA_CIRCULAR))
  {
    status = HAL_ERROR;
  }
  /* Check SDADC state */
  else if((hsdadc->State == HAL_SDADC_STATE_READY) || \
          (hsdadc->State == HAL_SDADC_STATE_INJ))
  {
    /* Set callbacks on DMA handler */
    hsdadc->hdma->XferCpltCallback = SDADC_DMARegularConvCplt;
    hsdadc->hdma->XferErrorCallback = SDADC_DMAError;
    if(hsdadc->hdma->Init.Mode == DMA_CIRCULAR)
    {
      hsdadc->hdma->XferHalfCpltCallback = SDADC_DMARegularHalfConvCplt;
    }

    /* Set RDMAEN bit in SDADC_CR1 register */
    hsdadc->Instance->CR1 |= SDADC_CR1_RDMAEN;

    /* Start DMA in interrupt mode */
    if(HAL_DMA_Start_IT(hsdadc->hdma, (uint32_t)&hsdadc->Instance->RDATAR, \
                        (uint32_t) pData, Length) != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_ERROR;
    }
    else
    {
      /* Start regular conversion */
      status = SDADC_RegConvStart(hsdadc);
    }
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to stop regular conversion in DMA mode.
  * @note   This function should be called only if regular conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_Stop_DMA(SDADC_HandleTypeDef *hsdadc)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check SDADC state */
  if((hsdadc->State != HAL_SDADC_STATE_REG) && \
     (hsdadc->State != HAL_SDADC_STATE_REG_INJ))
  {
    /* Return error status */
    status = HAL_ERROR;
  }
  else
  {
    /* Clear RDMAEN bit in SDADC_CR1 register */
    hsdadc->Instance->CR1 &= ~(SDADC_CR1_RDMAEN);

    /* Stop current DMA transfer */
    if(HAL_DMA_Abort(hsdadc->hdma) != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_ERROR;
    }
    else
    {
      /* Stop regular conversion */
      status = SDADC_RegConvStop(hsdadc);
    }
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to get regular conversion value.
  * @param  hsdadc SDADC handle.
  * @retval Regular conversion value
  */
uint32_t HAL_SDADC_GetValue(SDADC_HandleTypeDef *hsdadc)
{
  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Return regular conversion value */
  return hsdadc->Instance->RDATAR;
}

/**
  * @brief  This function allows to start injected conversion in polling mode.
  * @note   This function should be called only when SDADC instance is in idle state
  *         or if regular conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_InjectedStart(SDADC_HandleTypeDef *hsdadc)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check SDADC state */
  if((hsdadc->State == HAL_SDADC_STATE_READY) || \
     (hsdadc->State == HAL_SDADC_STATE_REG))
  {
    /* Start injected conversion */
    status = SDADC_InjConvStart(hsdadc);
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to poll for the end of injected conversion.
  * @note   This function should be called only if injected conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @param  Timeout Timeout value in milliseconds.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_PollForInjectedConversion(SDADC_HandleTypeDef* hsdadc,
                                                      uint32_t Timeout)
{
  uint32_t tickstart;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check SDADC state */
  if((hsdadc->State != HAL_SDADC_STATE_INJ) && \
     (hsdadc->State != HAL_SDADC_STATE_REG_INJ))
  {
    /* Return error status */
    return HAL_ERROR;
  }
  else
  {
    /* Get timeout */
    tickstart = HAL_GetTick();

    /* Wait JEOCF bit in SDADC_ISR register */
    while((hsdadc->Instance->ISR & SDADC_ISR_JEOCF) != SDADC_ISR_JEOCF)
    {
      /* Check the Timeout */
      if(Timeout != HAL_MAX_DELAY)
      {
        if(((HAL_GetTick()-tickstart) > Timeout) || (Timeout == 0UL))
        {
          /* Return timeout status */
          return HAL_TIMEOUT;
        }
      }
    }
    /* Check if overrun occurs */
    if((hsdadc->Instance->ISR & SDADC_ISR_JOVRF) == SDADC_ISR_JOVRF)
    {
      /* Update error code and call error callback */
      hsdadc->ErrorCode = SDADC_ERROR_INJECTED_OVERRUN;
#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
      hsdadc->ErrorCallback(hsdadc);
#else
      HAL_SDADC_ErrorCallback(hsdadc);
#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */

      /* Set CLRJOVRF bit in SDADC_CLRISR register */
      hsdadc->Instance->CLRISR |= SDADC_ISR_CLRJOVRF;
    }
    /* Update remaining injected conversions */
    hsdadc->InjConvRemaining--;
    if(hsdadc->InjConvRemaining == 0UL)
    {
      /* end of injected sequence, reset the value */
      hsdadc->InjConvRemaining = hsdadc->InjectedChannelsNbr;
    }

    /* Update SDADC state only if not continuous conversion, SW trigger */
    /* and end of injected sequence */
    if((hsdadc->InjectedContMode == SDADC_CONTINUOUS_CONV_OFF) && \
       (hsdadc->InjectedTrigger == SDADC_SOFTWARE_TRIGGER) && \
       (hsdadc->InjConvRemaining == hsdadc->InjectedChannelsNbr))
    {
      hsdadc->State = (hsdadc->State == HAL_SDADC_STATE_INJ) ? \
                      HAL_SDADC_STATE_READY : HAL_SDADC_STATE_REG;
    }
    /* Return function status */
    return HAL_OK;
  }
}

/**
  * @brief  This function allows to stop injected conversion in polling mode.
  * @note   This function should be called only if injected conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_InjectedStop(SDADC_HandleTypeDef *hsdadc)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check SDADC state */
  if((hsdadc->State != HAL_SDADC_STATE_INJ) && \
     (hsdadc->State != HAL_SDADC_STATE_REG_INJ))
  {
    /* Return error status */
    status = HAL_ERROR;
  }
  else
  {
    /* Stop injected conversion */
    status = SDADC_InjConvStop(hsdadc);
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to start injected conversion in interrupt mode.
  * @note   This function should be called only when SDADC instance is in idle state
  *         or if regular conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_InjectedStart_IT(SDADC_HandleTypeDef *hsdadc)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check SDADC state */
  if((hsdadc->State == HAL_SDADC_STATE_READY) || \
     (hsdadc->State == HAL_SDADC_STATE_REG))
  {
    /* Set JEOCIE and JOVRIE bits in SDADC_CR1 register */
    hsdadc->Instance->CR1 |= (uint32_t) (SDADC_CR1_JEOCIE | SDADC_CR1_JOVRIE);

    /* Start injected conversion */
    status = SDADC_InjConvStart(hsdadc);
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to stop injected conversion in interrupt mode.
  * @note   This function should be called only if injected conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_InjectedStop_IT(SDADC_HandleTypeDef *hsdadc)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check SDADC state */
  if((hsdadc->State != HAL_SDADC_STATE_INJ) && \
     (hsdadc->State != HAL_SDADC_STATE_REG_INJ))
  {
    /* Return error status */
    status = HAL_ERROR;
  }
  else
  {
    /* Clear JEOCIE and JOVRIE bits in SDADC_CR1 register */
    hsdadc->Instance->CR1 &= (uint32_t) ~(SDADC_CR1_JEOCIE | SDADC_CR1_JOVRIE);

    /* Stop injected conversion */
    status = SDADC_InjConvStop(hsdadc);
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to start injected conversion in DMA mode.
  * @note   This function should be called only when SDADC instance is in idle state
  *         or if regular conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @param  pData The destination buffer address.
  * @param  Length The length of data to be transferred from SDADC peripheral to memory.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_InjectedStart_DMA(SDADC_HandleTypeDef *hsdadc, uint32_t *pData,
                                              uint32_t Length)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(pData != ((void*) 0));
  assert_param(Length != 0UL);

  /* Check that DMA is not enabled for regular conversion */
  if((hsdadc->Instance->CR1 & SDADC_CR1_RDMAEN) == SDADC_CR1_RDMAEN)
  {
    status = HAL_ERROR;
  }
  /* Check parameters compatibility */
  else if((hsdadc->InjectedTrigger == SDADC_SOFTWARE_TRIGGER) && \
          (hsdadc->InjectedContMode == SDADC_CONTINUOUS_CONV_OFF) && \
          (hsdadc->hdma->Init.Mode == DMA_NORMAL) && \
          (Length > hsdadc->InjectedChannelsNbr))
  {
    status = HAL_ERROR;
  }
  else if((hsdadc->InjectedTrigger == SDADC_SOFTWARE_TRIGGER) && \
          (hsdadc->InjectedContMode == SDADC_CONTINUOUS_CONV_OFF) && \
          (hsdadc->hdma->Init.Mode == DMA_CIRCULAR))
  {
    status = HAL_ERROR;
  }
  /* Check SDADC state */
  else if((hsdadc->State == HAL_SDADC_STATE_READY) || \
          (hsdadc->State == HAL_SDADC_STATE_REG))
  {
    /* Set callbacks on DMA handler */
    hsdadc->hdma->XferCpltCallback = SDADC_DMAInjectedConvCplt;
    hsdadc->hdma->XferErrorCallback = SDADC_DMAError;
    if(hsdadc->hdma->Init.Mode == DMA_CIRCULAR)
    {
      hsdadc->hdma->XferHalfCpltCallback = SDADC_DMAInjectedHalfConvCplt;
    }

    /* Set JDMAEN bit in SDADC_CR1 register */
    hsdadc->Instance->CR1 |= SDADC_CR1_JDMAEN;

    /* Start DMA in interrupt mode */
    if(HAL_DMA_Start_IT(hsdadc->hdma, (uint32_t)&hsdadc->Instance->JDATAR, \
                        (uint32_t) pData, Length) != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_ERROR;
    }
    else
    {
      /* Start injected conversion */
      status = SDADC_InjConvStart(hsdadc);
    }
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to stop injected conversion in DMA mode.
  * @note   This function should be called only if injected conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_InjectedStop_DMA(SDADC_HandleTypeDef *hsdadc)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check SDADC state */
  if((hsdadc->State != HAL_SDADC_STATE_INJ) && \
     (hsdadc->State != HAL_SDADC_STATE_REG_INJ))
  {
    /* Return error status */
    status = HAL_ERROR;
  }
  else
  {
    /* Clear JDMAEN bit in SDADC_CR1 register */
    hsdadc->Instance->CR1 &= ~(SDADC_CR1_JDMAEN);

    /* Stop current DMA transfer */
    if(HAL_DMA_Abort(hsdadc->hdma) != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_ERROR;
    }
    else
    {
      /* Stop injected conversion */
      status = SDADC_InjConvStop(hsdadc);
    }
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to get injected conversion value.
  * @param  hsdadc SDADC handle.
  * @param  Channel Corresponding channel of injected conversion.
  * @retval Injected conversion value
  */
uint32_t HAL_SDADC_InjectedGetValue(SDADC_HandleTypeDef *hsdadc, uint32_t* Channel)
{
  uint32_t value;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(Channel != ((void*) 0));

  /* Read SDADC_JDATAR register and extract channel and conversion value */
  value = hsdadc->Instance->JDATAR;
  *Channel = ((value & SDADC_JDATAR_JDATACH) >> SDADC_JDATAR_CH_OFFSET);
  value &= SDADC_JDATAR_JDATA;

  /* Return injected conversion value */
  return value;
}

/**
  * @brief  This function allows to start multimode regular conversions in DMA mode.
  * @note   This function should be called only when SDADC instance is in idle state
  *         or if injected conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @param  pData The destination buffer address.
  * @param  Length The length of data to be transferred from SDADC peripheral to memory.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_MultiModeStart_DMA(SDADC_HandleTypeDef* hsdadc, uint32_t* pData,
                                               uint32_t Length)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(pData != ((void*) 0));
  assert_param(Length != 0UL);

  /* Check instance is SDADC1 */
  if(hsdadc->Instance != SDADC1)
  {
    status = HAL_ERROR;
  }
  /* Check that DMA is not enabled for injected conversion */
  else if((hsdadc->Instance->CR1 & SDADC_CR1_JDMAEN) == SDADC_CR1_JDMAEN)
  {
    status = HAL_ERROR;
  }
  /* Check parameters compatibility */
  else if((hsdadc->RegularTrigger == SDADC_SOFTWARE_TRIGGER) && \
          (hsdadc->RegularContMode == SDADC_CONTINUOUS_CONV_OFF) && \
          (hsdadc->hdma->Init.Mode == DMA_NORMAL) && \
          (Length != 1U))
  {
    status = HAL_ERROR;
  }
  else if((hsdadc->RegularTrigger == SDADC_SOFTWARE_TRIGGER) && \
          (hsdadc->RegularContMode == SDADC_CONTINUOUS_CONV_OFF) && \
          (hsdadc->hdma->Init.Mode == DMA_CIRCULAR))
  {
    status = HAL_ERROR;
  }
  /* Check SDADC state */
  else if((hsdadc->State == HAL_SDADC_STATE_READY) || \
          (hsdadc->State == HAL_SDADC_STATE_INJ))
  {
    /* Set callbacks on DMA handler */
    hsdadc->hdma->XferCpltCallback = SDADC_DMARegularConvCplt;
    hsdadc->hdma->XferErrorCallback = SDADC_DMAError;
    if(hsdadc->hdma->Init.Mode == DMA_CIRCULAR)
    {
      hsdadc->hdma->XferHalfCpltCallback = SDADC_DMARegularHalfConvCplt;
    }
    /* Set RDMAEN bit in SDADC_CR1 register */
    hsdadc->Instance->CR1 |= SDADC_CR1_RDMAEN;

    /* Start DMA in interrupt mode */
    if(hsdadc->RegularMultimode == SDADC_MULTIMODE_SDADC1_SDADC2)
    {
      status = HAL_DMA_Start_IT(hsdadc->hdma, (uint32_t)&hsdadc->Instance->RDATA12R, \
                                (uint32_t) pData, Length);
    }
    else
    {
      status = HAL_DMA_Start_IT(hsdadc->hdma, (uint32_t)&hsdadc->Instance->RDATA13R, \
                                (uint32_t) pData, Length);
    }
    if(status != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_ERROR;
    }
    else
    {
      /* Start regular conversion */
      status = SDADC_RegConvStart(hsdadc);
    }
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to stop multimode regular conversions in DMA mode.
  * @note   This function should be called only if regular conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_MultiModeStop_DMA(SDADC_HandleTypeDef* hsdadc)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check instance is SDADC1 */
  if(hsdadc->Instance != SDADC1)
  {
    status = HAL_ERROR;
  }
  /* Check SDADC state */
  else if((hsdadc->State != HAL_SDADC_STATE_REG) && \
          (hsdadc->State != HAL_SDADC_STATE_REG_INJ))
  {
    /* Return error status */
    status = HAL_ERROR;
  }
  else
  {
    /* Clear RDMAEN bit in SDADC_CR1 register */
    hsdadc->Instance->CR1 &= ~(SDADC_CR1_RDMAEN);

    /* Stop current DMA transfer */
    if(HAL_DMA_Abort(hsdadc->hdma) != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_ERROR;
    }
    else
    {
      /* Stop regular conversion */
      status = SDADC_RegConvStop(hsdadc);
    }
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to get multimode regular conversion value.
  * @param  hsdadc SDADC handle.
  * @retval Multimode regular conversion value
  */
uint32_t HAL_SDADC_MultiModeGetValue(SDADC_HandleTypeDef* hsdadc)
{
  uint32_t value;

  /* Check parameters and check instance is SDADC1 */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(hsdadc->Instance == SDADC1);

  /* read multimode regular value */
  value = (hsdadc->RegularMultimode == SDADC_MULTIMODE_SDADC1_SDADC2) ? \
          hsdadc->Instance->RDATA12R : hsdadc->Instance->RDATA13R;

  /* Return multimode regular conversions value */
  return value;
}

/**
  * @brief  This function allows to start multimode injected conversions in DMA mode.
  * @note   This function should be called only when SDADC instance is in idle state
  *         or if regular conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @param  pData The destination buffer address.
  * @param  Length The length of data to be transferred from SDADC peripheral to memory.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_InjectedMultiModeStart_DMA(SDADC_HandleTypeDef* hsdadc,
                                                       uint32_t* pData, uint32_t Length)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(pData != ((void*) 0));
  assert_param(Length != 0UL);

  /* Check instance is SDADC1 */
  if(hsdadc->Instance != SDADC1)
  {
    status = HAL_ERROR;
  }
  /* Check that DMA is not enabled for regular conversion */
  else if((hsdadc->Instance->CR1 & SDADC_CR1_RDMAEN) == SDADC_CR1_RDMAEN)
  {
    status = HAL_ERROR;
  }
  /* Check parameters compatibility */
  else if((hsdadc->InjectedTrigger == SDADC_SOFTWARE_TRIGGER) && \
          (hsdadc->InjectedContMode == SDADC_CONTINUOUS_CONV_OFF) && \
          (hsdadc->hdma->Init.Mode == DMA_NORMAL) && \
          (Length > (hsdadc->InjectedChannelsNbr << 1U)))
  {
    status = HAL_ERROR;
  }
  else if((hsdadc->InjectedTrigger == SDADC_SOFTWARE_TRIGGER) && \
          (hsdadc->InjectedContMode == SDADC_CONTINUOUS_CONV_OFF) && \
          (hsdadc->hdma->Init.Mode == DMA_CIRCULAR))
  {
    status = HAL_ERROR;
  }
  /* Check SDADC state */
  else if((hsdadc->State == HAL_SDADC_STATE_READY) || \
          (hsdadc->State == HAL_SDADC_STATE_REG))
  {
    /* Set callbacks on DMA handler */
    hsdadc->hdma->XferCpltCallback = SDADC_DMAInjectedConvCplt;
    hsdadc->hdma->XferErrorCallback = SDADC_DMAError;
    if(hsdadc->hdma->Init.Mode == DMA_CIRCULAR)
    {
      hsdadc->hdma->XferHalfCpltCallback = SDADC_DMAInjectedHalfConvCplt;
    }
    /* Set JDMAEN bit in SDADC_CR1 register */
    hsdadc->Instance->CR1 |= SDADC_CR1_JDMAEN;

    /* Start DMA in interrupt mode */
    if(hsdadc->InjectedMultimode == SDADC_MULTIMODE_SDADC1_SDADC2)
    {
      status = HAL_DMA_Start_IT(hsdadc->hdma, (uint32_t)&hsdadc->Instance->JDATA12R, \
                                (uint32_t) pData, Length);
    }
    else
    {
      status = HAL_DMA_Start_IT(hsdadc->hdma, (uint32_t)&hsdadc->Instance->JDATA13R, \
                                (uint32_t) pData, Length);
    }
    if(status != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_ERROR;
    }
    else
    {
      /* Start injected conversion */
      status = SDADC_InjConvStart(hsdadc);
    }
  }
  else
  {
    status = HAL_ERROR;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to stop multimode injected conversions in DMA mode.
  * @note   This function should be called only if injected conversion is ongoing.
  * @param  hsdadc SDADC handle.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_SDADC_InjectedMultiModeStop_DMA(SDADC_HandleTypeDef* hsdadc)
{
  HAL_StatusTypeDef status;

  /* Check parameters */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));

  /* Check instance is SDADC1 */
  if(hsdadc->Instance != SDADC1)
  {
    status = HAL_ERROR;
  }
  /* Check SDADC state */
  else if((hsdadc->State != HAL_SDADC_STATE_INJ) && \
          (hsdadc->State != HAL_SDADC_STATE_REG_INJ))
  {
    /* Return error status */
    status = HAL_ERROR;
  }
  else
  {
    /* Clear JDMAEN bit in SDADC_CR1 register */
    hsdadc->Instance->CR1 &= ~(SDADC_CR1_JDMAEN);

    /* Stop current DMA transfer */
    if(HAL_DMA_Abort(hsdadc->hdma) != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_ERROR;
    }
    else
    {
      /* Stop injected conversion */
      status = SDADC_InjConvStop(hsdadc);
    }
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to get multimode injected conversion value.
  * @param  hsdadc SDADC handle.
  * @retval Multimode injected conversion value
  */
uint32_t HAL_SDADC_InjectedMultiModeGetValue(SDADC_HandleTypeDef* hsdadc)
{
  uint32_t value;

  /* Check parameters and check instance is SDADC1 */
  assert_param(IS_SDADC_ALL_INSTANCE(hsdadc->Instance));
  assert_param(hsdadc->Instance == SDADC1);

  /* read multimode injected value */
  value = (hsdadc->InjectedMultimode == SDADC_MULTIMODE_SDADC1_SDADC2) ? \
          hsdadc->Instance->JDATA12R : hsdadc->Instance->JDATA13R;

  /* Return multimode injected conversions value */
  return value;
}

/**
  * @brief  This function handles the SDADC interrupts.
  * @param  hsdadc SDADC handle.
  * @retval None
  */
void HAL_SDADC_IRQHandler(SDADC_HandleTypeDef* hsdadc)
{
  uint32_t tmp_isr = hsdadc->Instance->ISR;
  uint32_t tmp_cr1 = hsdadc->Instance->CR1;

  /* Check if end of regular conversion */
  if(((tmp_cr1 & SDADC_CR1_REOCIE) == SDADC_CR1_REOCIE) &&
     ((tmp_isr & SDADC_ISR_REOCF) == SDADC_ISR_REOCF))
  {
    /* Call regular conversion complete callback */
#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
    hsdadc->ConvCpltCallback(hsdadc);
#else
    HAL_SDADC_ConvCpltCallback(hsdadc);
#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */

    /* End of conversion if mode is not continuous and software trigger */
    if((hsdadc->RegularContMode == SDADC_CONTINUOUS_CONV_OFF) && \
       (hsdadc->RegularTrigger == SDADC_SOFTWARE_TRIGGER))
    {
      /* Clear REOCIE and ROVRIE bits in SDADC_CR1 register */
      hsdadc->Instance->CR1 &= ~(SDADC_CR1_REOCIE | SDADC_CR1_ROVRIE);

      /* Update SDADC state */
      hsdadc->State = (hsdadc->State == HAL_SDADC_STATE_REG) ? \
                      HAL_SDADC_STATE_READY : HAL_SDADC_STATE_INJ;
    }
  }
  /* Check if end of injected conversion */
  else if(((tmp_cr1 & SDADC_CR1_JEOCIE) == SDADC_CR1_JEOCIE) &&
          ((tmp_isr & SDADC_ISR_JEOCF) == SDADC_ISR_JEOCF))
  {
    /* Call injected conversion complete callback */
#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
    hsdadc->InjectedConvCpltCallback(hsdadc);
#else
    HAL_SDADC_InjectedConvCpltCallback(hsdadc);
#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */

    /* Update remaining injected conversions */
    hsdadc->InjConvRemaining--;
    if(hsdadc->InjConvRemaining ==0UL)
    {
      /* end of injected sequence, reset the value */
      hsdadc->InjConvRemaining = hsdadc->InjectedChannelsNbr;
    }
    /* End of conversion if mode is not continuous, software trigger */
    /* and end of injected sequence */
    if((hsdadc->InjectedContMode == SDADC_CONTINUOUS_CONV_OFF) && \
       (hsdadc->InjectedTrigger == SDADC_SOFTWARE_TRIGGER) && \
       (hsdadc->InjConvRemaining == hsdadc->InjectedChannelsNbr))
    {
      /* Clear JEOCIE and JOVRIE bits in SDADC_CR1 register */
      hsdadc->Instance->CR1 &= ~(SDADC_CR1_JEOCIE | SDADC_CR1_JOVRIE);

      /* Update SDADC state */
      hsdadc->State = (hsdadc->State == HAL_SDADC_STATE_INJ) ? \
                      HAL_SDADC_STATE_READY : HAL_SDADC_STATE_REG;
    }
  }
  /* Check if end of calibration */
  else if(((tmp_cr1 & SDADC_CR1_EOCALIE) == SDADC_CR1_EOCALIE) &&
          ((tmp_isr & SDADC_ISR_EOCALF) == SDADC_ISR_EOCALF))
  {
    /* Clear EOCALIE bit in SDADC_CR1 register */
    hsdadc->Instance->CR1 &= ~(SDADC_CR1_EOCALIE);

    /* Set CLREOCALF bit in SDADC_CLRISR register */
    hsdadc->Instance->CLRISR |= SDADC_ISR_CLREOCALF;

    /* Call calibration callback */
#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
    hsdadc->CalibrationCpltCallback(hsdadc);
#else
    HAL_SDADC_CalibrationCpltCallback(hsdadc);
#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */

    /* Update SDADC state */
    hsdadc->State = HAL_SDADC_STATE_READY;
  }
  /* Check if overrun occurs during regular conversion */
  else if(((tmp_cr1 & SDADC_CR1_ROVRIE) == SDADC_CR1_ROVRIE) &&
          ((tmp_isr & SDADC_ISR_ROVRF) == SDADC_ISR_ROVRF))
  {
    /* Set CLRROVRF bit in SDADC_CLRISR register */
    hsdadc->Instance->CLRISR |= SDADC_ISR_CLRROVRF;

    /* Update error code */
    hsdadc->ErrorCode = SDADC_ERROR_REGULAR_OVERRUN;

    /* Call error callback */
#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
    hsdadc->ErrorCallback(hsdadc);
#else
    HAL_SDADC_ErrorCallback(hsdadc);
#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */
  }
  /* Check if overrun occurs during injected conversion */
  else if(((tmp_cr1 & SDADC_CR1_JOVRIE) == SDADC_CR1_JOVRIE) &&
          ((tmp_isr & SDADC_ISR_JOVRF) == SDADC_ISR_JOVRF))
  {
    /* Set CLRJOVRF bit in SDADC_CLRISR register */
    hsdadc->Instance->CLRISR |= SDADC_ISR_CLRJOVRF;

    /* Update error code */
    hsdadc->ErrorCode = SDADC_ERROR_INJECTED_OVERRUN;

    /* Call error callback */
#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
    hsdadc->ErrorCallback(hsdadc);
#else
    HAL_SDADC_ErrorCallback(hsdadc);
#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */
  }
  else
  {
    /* No additional IRQ source */
  }

  return;
}

/**
  * @brief  Calibration complete callback.
  * @param  hsdadc SDADC handle.
  * @retval None
  */
__weak void HAL_SDADC_CalibrationCpltCallback(SDADC_HandleTypeDef* hsdadc)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hsdadc);

  /* NOTE : This function should not be modified, when the callback is needed,
            the HAL_SDADC_CalibrationCpltCallback could be implemented in the user file
   */
}

/**
  * @brief  Half regular conversion complete callback.
  * @param  hsdadc SDADC handle.
  * @retval None
  */
__weak void HAL_SDADC_ConvHalfCpltCallback(SDADC_HandleTypeDef* hsdadc)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hsdadc);

  /* NOTE : This function should not be modified, when the callback is needed,
            the HAL_SDADC_ConvHalfCpltCallback could be implemented in the user file
   */
}

/**
  * @brief  Regular conversion complete callback.
  * @note   In interrupt mode, user has to read conversion value in this function
            using HAL_SDADC_GetValue or HAL_SDADC_MultiModeGetValue.
  * @param  hsdadc SDADC handle.
  * @retval None
  */
__weak void HAL_SDADC_ConvCpltCallback(SDADC_HandleTypeDef* hsdadc)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hsdadc);

  /* NOTE : This function should not be modified, when the callback is needed,
            the HAL_SDADC_ConvCpltCallback could be implemented in the user file.
   */
}

/**
  * @brief  Half injected conversion complete callback.
  * @param  hsdadc SDADC handle.
  * @retval None
  */
__weak void HAL_SDADC_InjectedConvHalfCpltCallback(SDADC_HandleTypeDef* hsdadc)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hsdadc);

  /* NOTE : This function should not be modified, when the callback is needed,
            the HAL_SDADC_InjectedConvHalfCpltCallback could be implemented in the user file.
   */
}

/**
  * @brief  Injected conversion complete callback.
  * @note   In interrupt mode, user has to read conversion value in this function
            using HAL_SDADC_InjectedGetValue or HAL_SDADC_InjectedMultiModeGetValue.
  * @param  hsdadc SDADC handle.
  * @retval None
  */
__weak void HAL_SDADC_InjectedConvCpltCallback(SDADC_HandleTypeDef* hsdadc)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hsdadc);

  /* NOTE : This function should not be modified, when the callback is needed,
            the HAL_SDADC_InjectedConvCpltCallback could be implemented in the user file.
   */
}

/**
  * @brief  Error callback.
  * @param  hsdadc SDADC handle.
  * @retval None
  */
__weak void HAL_SDADC_ErrorCallback(SDADC_HandleTypeDef* hsdadc)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hsdadc);

  /* NOTE : This function should not be modified, when the callback is needed,
            the HAL_SDADC_ErrorCallback could be implemented in the user file.
   */
}

/**
  * @brief  DMA half transfer complete callback for regular conversion.
  * @param  hdma DMA handle.
  * @retval None
  */
static void SDADC_DMARegularHalfConvCplt(DMA_HandleTypeDef *hdma)
{
  /* Get SDADC handle */
  SDADC_HandleTypeDef* hsdadc = (SDADC_HandleTypeDef*) ((DMA_HandleTypeDef*)hdma)->Parent;

  /* Call regular half conversion complete callback */
#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
  hsdadc->ConvHalfCpltCallback(hsdadc);
#else
  HAL_SDADC_ConvHalfCpltCallback(hsdadc);
#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */
}

/**
  * @brief  DMA transfer complete callback for regular conversion.
  * @param  hdma DMA handle.
  * @retval None
  */
static void SDADC_DMARegularConvCplt(DMA_HandleTypeDef *hdma)
{
  /* Get SDADC handle */
  SDADC_HandleTypeDef* hsdadc = (SDADC_HandleTypeDef*) ((DMA_HandleTypeDef*)hdma)->Parent;

  /* Call regular conversion complete callback */
#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
  hsdadc->ConvCpltCallback(hsdadc);
#else
  HAL_SDADC_ConvCpltCallback(hsdadc);
#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */
}

/**
  * @brief  DMA half transfer complete callback for injected conversion.
  * @param  hdma DMA handle.
  * @retval None
  */
static void SDADC_DMAInjectedHalfConvCplt(DMA_HandleTypeDef *hdma)
{
  /* Get SDADC handle */
  SDADC_HandleTypeDef* hsdadc = (SDADC_HandleTypeDef*) ((DMA_HandleTypeDef*)hdma)->Parent;

  /* Call injected half conversion complete callback */
#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
  hsdadc->InjectedConvHalfCpltCallback(hsdadc);
#else
  HAL_SDADC_InjectedConvHalfCpltCallback(hsdadc);
#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */
}

/**
  * @brief  DMA transfer complete callback for injected conversion.
  * @param  hdma DMA handle.
  * @retval None
  */
static void SDADC_DMAInjectedConvCplt(DMA_HandleTypeDef *hdma)
{
  /* Get SDADC handle */
  SDADC_HandleTypeDef* hsdadc = (SDADC_HandleTypeDef*) ((DMA_HandleTypeDef*)hdma)->Parent;

  /* Call injected conversion complete callback */
#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
  hsdadc->InjectedConvCpltCallback(hsdadc);
#else
  HAL_SDADC_InjectedConvCpltCallback(hsdadc);
#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */
}

/**
  * @brief  DMA error callback.
  * @param  hdma DMA handle.
  * @retval None
  */
static void SDADC_DMAError(DMA_HandleTypeDef *hdma)
{
  /* Get SDADC handle */
  SDADC_HandleTypeDef* hsdadc = (SDADC_HandleTypeDef*) ((DMA_HandleTypeDef*)hdma)->Parent;

  /* Update error code */
  hsdadc->ErrorCode = SDADC_ERROR_DMA;

  /* Call error callback */
#if (USE_HAL_SDADC_REGISTER_CALLBACKS == 1)
  hsdadc->ErrorCallback(hsdadc);
#else
  HAL_SDADC_ErrorCallback(hsdadc);
#endif /* USE_HAL_SDADC_REGISTER_CALLBACKS */
}

/**
  * @}
  */

/** @defgroup SDADC_Exported_Functions_Group4 Peripheral State functions
 *  @brief   SDADC Peripheral State functions
 *
@verbatim
  ===============================================================================
             ##### ADC Peripheral State functions #####
  ===============================================================================
    [..] This subsection provides functions allowing to
      (+) Get the SDADC state
      (+) Get the SDADC Error

@endverbatim
  * @{
  */

/**
  * @brief  This function allows to get the current SDADC state.
  * @param  hsdadc SDADC handle.
  * @retval SDADC state.
  */
HAL_SDADC_StateTypeDef HAL_SDADC_GetState(SDADC_HandleTypeDef* hsdadc)
{
  return hsdadc->State;
}

/**
  * @brief  This function allows to get the current SDADC error code.
  * @param  hsdadc SDADC handle.
  * @retval SDADC error code.
  */
uint32_t HAL_SDADC_GetError(SDADC_HandleTypeDef* hsdadc)
{
  return hsdadc->ErrorCode;
}

/**
  * @}
  */

/** @addtogroup SDADC_Private_Functions SDADC Private Functions
  * @{
  */

/**
  * @brief  This function allows to enter in init mode for SDADC instance.
  * @param  hsdadc SDADC handle.
  * @retval HAL status.
  */
static HAL_StatusTypeDef SDADC_EnterInitMode(SDADC_HandleTypeDef* hsdadc)
{
  uint32_t tickstart;

  /* Set INIT bit on SDADC_CR1 register */
  hsdadc->Instance->CR1 |= SDADC_CR1_INIT;

  /* Wait INITRDY bit on SDADC_ISR */
  tickstart = HAL_GetTick();
  while((hsdadc->Instance->ISR & SDADC_ISR_INITRDY) == (uint32_t)RESET)
  {
    if((HAL_GetTick()-tickstart) > SDADC_TIMEOUT)
    {
      return HAL_TIMEOUT;
    }
  }

  /* Return HAL status */
  return HAL_OK;
}

/**
  * @brief  This function allows to exit from init mode for SDADC instance.
  * @param  hsdadc SDADC handle.
  * @retval None.
  */
static void SDADC_ExitInitMode(SDADC_HandleTypeDef* hsdadc)
{
  /* Reset INIT bit in SDADC_CR1 register */
  hsdadc->Instance->CR1 &= ~(SDADC_CR1_INIT);
}

/**
  * @brief  This function allows to get the number of injected channels.
  * @param  Channels bitfield of injected channels.
  * @retval Number of injected channels.
  */
static uint32_t SDADC_GetInjChannelsNbr(uint32_t Channels)
{
  uint32_t nbChannels = 0UL;
  uint32_t tmp,i;

  /* Get the number of channels from bitfield */
  tmp = (uint32_t) (Channels & SDADC_LSB_MASK);
  for(i = 0UL ; i < 9UL ; i++)
  {
    if((tmp & 0x00000001UL) != 0UL)
    {
      nbChannels++;
    }
    tmp = (uint32_t) (tmp >> 1UL);
  }
  return nbChannels;
}

/**
  * @brief  This function allows to really start regular conversion.
  * @param  hsdadc SDADC handle.
  * @retval HAL status.
  */
static HAL_StatusTypeDef SDADC_RegConvStart(SDADC_HandleTypeDef* hsdadc)
{
  HAL_StatusTypeDef status = HAL_OK;

  /* Check regular trigger */
  if(hsdadc->RegularTrigger == SDADC_SOFTWARE_TRIGGER)
  {
    /* Set RSWSTART bit in SDADC_CR2 register */
    hsdadc->Instance->CR2 |= SDADC_CR2_RSWSTART;
  }
  else /* synchronous trigger */
  {
    /* Enter init mode */
    if(SDADC_EnterInitMode(hsdadc) != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_TIMEOUT;
    }
    else
    {
      /* Set RSYNC bit in SDADC_CR1 register */
      hsdadc->Instance->CR1 |= SDADC_CR1_RSYNC;

      /* Exit init mode */
      SDADC_ExitInitMode(hsdadc);
    }
  }
  /* Update SDADC state only if status is OK */
  if(status == HAL_OK)
  {
    hsdadc->State = (hsdadc->State == HAL_SDADC_STATE_READY) ? \
                    HAL_SDADC_STATE_REG : HAL_SDADC_STATE_REG_INJ;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to really stop regular conversion.
  * @param  hsdadc SDADC handle.
  * @retval HAL status.
  */
static HAL_StatusTypeDef SDADC_RegConvStop(SDADC_HandleTypeDef* hsdadc)
{
  uint32_t tickstart;
  __IO uint32_t dummy_read_for_register_reset;

  /* Check continuous mode */
  if(hsdadc->RegularContMode == SDADC_CONTINUOUS_CONV_ON)
  {
    /* Clear REOCF by reading SDADC_RDATAR register */
    dummy_read_for_register_reset = hsdadc->Instance->RDATAR;
    UNUSED(dummy_read_for_register_reset);

    /* Clear RCONT bit in SDADC_CR2 register */
    hsdadc->Instance->CR2 &= ~(SDADC_CR2_RCONT);
  }
  /* Wait for the end of regular conversion */
  tickstart = HAL_GetTick();
  while((hsdadc->Instance->ISR & SDADC_ISR_RCIP) != 0UL)
  {
    if((HAL_GetTick()-tickstart) > SDADC_TIMEOUT)
    {
      /* Set SDADC in error state and return timeout status */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      return HAL_TIMEOUT;
    }
  }
  /* Check if trigger is synchronous */
  if(hsdadc->RegularTrigger == SDADC_SYNCHRONOUS_TRIGGER)
  {
    /* Enter init mode */
    if(SDADC_EnterInitMode(hsdadc) != HAL_OK)
    {
      /* Set SDADC in error state and return timeout status */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      return HAL_TIMEOUT;
    }
    else
    {
      /* Clear RSYNC bit in SDADC_CR1 register */
      hsdadc->Instance->CR1 &= ~(SDADC_CR1_RSYNC);

      /* Exit init mode */
      SDADC_ExitInitMode(hsdadc);
    }
  }
  /* Check if continuous mode */
  if(hsdadc->RegularContMode == SDADC_CONTINUOUS_CONV_ON)
  {
    /* Restore RCONT bit in SDADC_CR2 register */
    hsdadc->Instance->CR2 |= SDADC_CR2_RCONT;
  }
  /* Clear REOCF by reading SDADC_RDATAR register */
  dummy_read_for_register_reset = hsdadc->Instance->RDATAR;
  UNUSED(dummy_read_for_register_reset);

  /* Set CLRROVRF bit in SDADC_CLRISR register */
  hsdadc->Instance->CLRISR |= SDADC_ISR_CLRROVRF;

  /* Update SDADC state */
  hsdadc->State = (hsdadc->State == HAL_SDADC_STATE_REG) ? \
                  HAL_SDADC_STATE_READY : HAL_SDADC_STATE_INJ;

  /* Return function status */
  return HAL_OK;
}

/**
  * @brief  This function allows to really start injected conversion.
  * @param  hsdadc SDADC handle.
  * @retval HAL status.
  */
static HAL_StatusTypeDef SDADC_InjConvStart(SDADC_HandleTypeDef* hsdadc)
{
  HAL_StatusTypeDef status = HAL_OK;

  /* Initialize number of injected conversions remaining */
  hsdadc->InjConvRemaining = hsdadc->InjectedChannelsNbr;

  /* Check injected trigger */
  if(hsdadc->InjectedTrigger == SDADC_SOFTWARE_TRIGGER)
  {
    /* Set JSWSTART bit in SDADC_CR2 register */
    hsdadc->Instance->CR2 |= SDADC_CR2_JSWSTART;
  }
  else /* external or synchronous trigger */
  {
    /* Enter init mode */
    if(SDADC_EnterInitMode(hsdadc) != HAL_OK)
    {
      /* Set SDADC in error state */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      status = HAL_TIMEOUT;
    }
    else
    {
      if(hsdadc->InjectedTrigger == SDADC_SYNCHRONOUS_TRIGGER)
      {
        /* Set JSYNC bit in SDADC_CR1 register */
        hsdadc->Instance->CR1 |= SDADC_CR1_JSYNC;
      }
      else /* external trigger */
      {
        /* Set JEXTEN[1:0] bits in SDADC_CR2 register */
        hsdadc->Instance->CR2 |= hsdadc->ExtTriggerEdge;
      }
      /* Exit init mode */
      SDADC_ExitInitMode(hsdadc);
    }
  }
  /* Update SDADC state only if status is OK */
  if(status == HAL_OK)
  {
    hsdadc->State = (hsdadc->State == HAL_SDADC_STATE_READY) ? \
                    HAL_SDADC_STATE_INJ : HAL_SDADC_STATE_REG_INJ;
  }
  /* Return function status */
  return status;
}

/**
  * @brief  This function allows to really stop injected conversion.
  * @param  hsdadc SDADC handle.
  * @retval HAL status.
  */
static HAL_StatusTypeDef SDADC_InjConvStop(SDADC_HandleTypeDef* hsdadc)
{
  uint32_t tickstart;
  __IO uint32_t dummy_read_for_register_reset;

  /* Check continuous mode */
  if(hsdadc->InjectedContMode == SDADC_CONTINUOUS_CONV_ON)
  {
    /* Clear JEOCF by reading SDADC_JDATAR register */
    dummy_read_for_register_reset =  hsdadc->Instance->JDATAR;
    UNUSED(dummy_read_for_register_reset);

    /* Clear JCONT bit in SDADC_CR2 register */
    hsdadc->Instance->CR2 &= ~(SDADC_CR2_JCONT);
  }
  /* Wait for the end of injected conversion */
  tickstart = HAL_GetTick();
  while((hsdadc->Instance->ISR & SDADC_ISR_JCIP) != 0UL)
  {
    if((HAL_GetTick()-tickstart) > SDADC_TIMEOUT)
    {
      /* Set SDADC in error state and return timeout status */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      return HAL_TIMEOUT;
    }
  }
  /* Check if trigger is not software */
  if(hsdadc->InjectedTrigger != SDADC_SOFTWARE_TRIGGER)
  {
    /* Enter init mode */
    if(SDADC_EnterInitMode(hsdadc) != HAL_OK)
    {
      /* Set SDADC in error state and return timeout status */
      hsdadc->State = HAL_SDADC_STATE_ERROR;
      return HAL_TIMEOUT;
    }
    else
    {
      /* Check if trigger is synchronous */
      if(hsdadc->InjectedTrigger == SDADC_SYNCHRONOUS_TRIGGER)
      {
        /* Clear JSYNC bit in SDADC_CR1 register */
        hsdadc->Instance->CR1 &= ~(SDADC_CR1_JSYNC);
      }
      else /* external trigger */
      {
        /* Clear JEXTEN[1:0] bits in SDADC_CR2 register */
        hsdadc->Instance->CR2 &= ~(SDADC_CR2_JEXTEN);
      }
      /* Exit init mode */
      SDADC_ExitInitMode(hsdadc);
    }
  }
  /* Check if continuous mode */
  if(hsdadc->InjectedContMode == SDADC_CONTINUOUS_CONV_ON)
  {
    /* Restore JCONT bit in SDADC_CR2 register */
    hsdadc->Instance->CR2 |= SDADC_CR2_JCONT;
  }
  /* Clear JEOCF by reading SDADC_JDATAR register */
  dummy_read_for_register_reset = hsdadc->Instance->JDATAR;
  UNUSED(dummy_read_for_register_reset);

  /* Set CLRJOVRF bit in SDADC_CLRISR register */
  hsdadc->Instance->CLRISR |= SDADC_ISR_CLRJOVRF;

  /* Update SDADC state */
  hsdadc->State = (hsdadc->State == HAL_SDADC_STATE_INJ) ? \
                  HAL_SDADC_STATE_READY : HAL_SDADC_STATE_REG;

  /* Return function status */
  return HAL_OK;
}

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

#endif /* SDADC1 || SDADC2 || SDADC3 */
#endif /* HAL_SDADC_MODULE_ENABLED */
/**
  * @}
  */