V9_PMU/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_ll_gpio.h

/**
  ******************************************************************************
  * @file    stm32f1xx_ll_gpio.h
  * @author  MCD Application Team
  * @brief   Header file of GPIO LL module.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32F1xx_LL_GPIO_H
#define STM32F1xx_LL_GPIO_H

#ifdef __cplusplus
extern "C" {
#endif

/* Includes ------------------------------------------------------------------*/
#include "stm32f1xx.h"

/** @addtogroup STM32F1xx_LL_Driver
  * @{
  */

#if defined (GPIOA) || defined (GPIOB) || defined (GPIOC) || defined (GPIOD) || defined (GPIOE) || defined (GPIOF) || defined (GPIOG)

/** @defgroup GPIO_LL GPIO
  * @{
  */

/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/

/** @defgroup GPIO_LL_Private_Constants GPIO Private Constants
  * @{
  */
/* Defines used for Pin Mask Initialization */
#define GPIO_PIN_MASK_POS   8U
#define GPIO_PIN_NB         16U
/**
  * @}
  */

/* Private macros ------------------------------------------------------------*/
#if defined(USE_FULL_LL_DRIVER)
/** @defgroup GPIO_LL_Private_Macros GPIO Private Macros
  * @{
  */

/**
  * @}
  */
#endif /*USE_FULL_LL_DRIVER*/

/* Exported types ------------------------------------------------------------*/
#if defined(USE_FULL_LL_DRIVER)
/** @defgroup GPIO_LL_ES_INIT GPIO Exported Init structures
  * @{
  */

/**
  * @brief LL GPIO Init Structure definition
  */
typedef struct
{
  uint32_t Pin;          /*!< Specifies the GPIO pins to be configured.
                              This parameter can be any value of @ref GPIO_LL_EC_PIN */

  uint32_t Mode;         /*!< Specifies the operating mode for the selected pins.
                              This parameter can be a value of @ref GPIO_LL_EC_MODE.

                              GPIO HW configuration can be modified afterwards using unitary function @ref LL_GPIO_SetPinMode().*/

  uint32_t Speed;        /*!< Specifies the speed for the selected pins.
                              This parameter can be a value of @ref GPIO_LL_EC_SPEED.

                              GPIO HW configuration can be modified afterwards using unitary function @ref LL_GPIO_SetPinSpeed().*/

  uint32_t OutputType;   /*!< Specifies the operating output type for the selected pins.
                              This parameter can be a value of @ref GPIO_LL_EC_OUTPUT.

                              GPIO HW configuration can be modified afterwards using unitary function @ref LL_GPIO_SetPinOutputType().*/

  uint32_t Pull;         /*!< Specifies the operating Pull-up/Pull down for the selected pins.
                              This parameter can be a value of @ref GPIO_LL_EC_PULL.

                              GPIO HW configuration can be modified afterwards using unitary function @ref LL_GPIO_SetPinPull().*/
} LL_GPIO_InitTypeDef;

/**
  * @}
  */
#endif /* USE_FULL_LL_DRIVER */

/* Exported constants --------------------------------------------------------*/
/** @defgroup GPIO_LL_Exported_Constants GPIO Exported Constants
  * @{
  */

/** @defgroup GPIO_LL_EC_PIN PIN
  * @{
  */
#define LL_GPIO_PIN_0                    ((GPIO_BSRR_BS0  << GPIO_PIN_MASK_POS) | 0x00000001U)  /*!< Select pin 0  */
#define LL_GPIO_PIN_1                    ((GPIO_BSRR_BS1  << GPIO_PIN_MASK_POS) | 0x00000002U)  /*!< Select pin 1  */
#define LL_GPIO_PIN_2                    ((GPIO_BSRR_BS2  << GPIO_PIN_MASK_POS) | 0x00000004U)  /*!< Select pin 2  */
#define LL_GPIO_PIN_3                    ((GPIO_BSRR_BS3  << GPIO_PIN_MASK_POS) | 0x00000008U)  /*!< Select pin 3  */
#define LL_GPIO_PIN_4                    ((GPIO_BSRR_BS4  << GPIO_PIN_MASK_POS) | 0x00000010U)  /*!< Select pin 4  */
#define LL_GPIO_PIN_5                    ((GPIO_BSRR_BS5  << GPIO_PIN_MASK_POS) | 0x00000020U)  /*!< Select pin 5  */
#define LL_GPIO_PIN_6                    ((GPIO_BSRR_BS6  << GPIO_PIN_MASK_POS) | 0x00000040U)  /*!< Select pin 6  */
#define LL_GPIO_PIN_7                    ((GPIO_BSRR_BS7  << GPIO_PIN_MASK_POS) | 0x00000080U)  /*!< Select pin 7  */
#define LL_GPIO_PIN_8                    ((GPIO_BSRR_BS8  << GPIO_PIN_MASK_POS) | 0x04000001U)  /*!< Select pin 8  */
#define LL_GPIO_PIN_9                    ((GPIO_BSRR_BS9  << GPIO_PIN_MASK_POS) | 0x04000002U)  /*!< Select pin 9  */
#define LL_GPIO_PIN_10                   ((GPIO_BSRR_BS10 << GPIO_PIN_MASK_POS) | 0x04000004U)  /*!< Select pin 10 */
#define LL_GPIO_PIN_11                   ((GPIO_BSRR_BS11 << GPIO_PIN_MASK_POS) | 0x04000008U)  /*!< Select pin 11 */
#define LL_GPIO_PIN_12                   ((GPIO_BSRR_BS12 << GPIO_PIN_MASK_POS) | 0x04000010U)  /*!< Select pin 12 */
#define LL_GPIO_PIN_13                   ((GPIO_BSRR_BS13 << GPIO_PIN_MASK_POS) | 0x04000020U)  /*!< Select pin 13 */
#define LL_GPIO_PIN_14                   ((GPIO_BSRR_BS14 << GPIO_PIN_MASK_POS) | 0x04000040U)  /*!< Select pin 14 */
#define LL_GPIO_PIN_15                   ((GPIO_BSRR_BS15 << GPIO_PIN_MASK_POS) | 0x04000080U)  /*!< Select pin 15 */
#define LL_GPIO_PIN_ALL                  (LL_GPIO_PIN_0  | LL_GPIO_PIN_1  | LL_GPIO_PIN_2  | \
                                          LL_GPIO_PIN_3  | LL_GPIO_PIN_4  | LL_GPIO_PIN_5  | \
                                          LL_GPIO_PIN_6  | LL_GPIO_PIN_7  | LL_GPIO_PIN_8  | \
                                          LL_GPIO_PIN_9  | LL_GPIO_PIN_10 | LL_GPIO_PIN_11 | \
                                          LL_GPIO_PIN_12 | LL_GPIO_PIN_13 | LL_GPIO_PIN_14 | \
                                          LL_GPIO_PIN_15)                                      /*!< Select all pins */
/**
  * @}
  */

/** @defgroup GPIO_LL_EC_MODE Mode
  * @{
  */
#define LL_GPIO_MODE_ANALOG              0x00000000U       /*!< Select analog mode */
#define LL_GPIO_MODE_FLOATING            GPIO_CRL_CNF0_0   /*!< Select floating mode */
#define LL_GPIO_MODE_INPUT               GPIO_CRL_CNF0_1   /*!< Select input mode */
#define LL_GPIO_MODE_OUTPUT              GPIO_CRL_MODE0_0  /*!< Select general purpose output mode */
#define LL_GPIO_MODE_ALTERNATE           (GPIO_CRL_CNF0_1 | GPIO_CRL_MODE0_0) /*!< Select alternate function mode */
/**
  * @}
  */

/** @defgroup GPIO_LL_EC_OUTPUT Output Type
  * @{
  */
#define LL_GPIO_OUTPUT_PUSHPULL          0x00000000U                /*!< Select push-pull as output type */
#define LL_GPIO_OUTPUT_OPENDRAIN         GPIO_CRL_CNF0_0            /*!< Select open-drain as output type */
/**
  * @}
  */

/** @defgroup GPIO_LL_EC_SPEED Output Speed
  * @{
  */
#define LL_GPIO_MODE_OUTPUT_10MHz        GPIO_CRL_MODE0_0            /*!< Select Output mode, max speed 10 MHz */
#define LL_GPIO_MODE_OUTPUT_2MHz         GPIO_CRL_MODE0_1            /*!< Select Output mode, max speed 20 MHz */
#define LL_GPIO_MODE_OUTPUT_50MHz        GPIO_CRL_MODE0              /*!< Select Output mode, max speed 50 MHz */
/**
  * @}
  */

#define LL_GPIO_SPEED_FREQ_LOW           LL_GPIO_MODE_OUTPUT_2MHz    /*!< Select I/O low output speed    */
#define LL_GPIO_SPEED_FREQ_MEDIUM        LL_GPIO_MODE_OUTPUT_10MHz   /*!< Select I/O medium output speed */
#define LL_GPIO_SPEED_FREQ_HIGH          LL_GPIO_MODE_OUTPUT_50MHz   /*!< Select I/O high output speed   */

/** @defgroup GPIO_LL_EC_PULL Pull Up Pull Down
  * @{
  */
#define LL_GPIO_PULL_DOWN                0x00000000U    /*!< Select I/O pull down */
#define LL_GPIO_PULL_UP                  GPIO_ODR_ODR0  /*!< Select I/O pull up */

/**
  * @}
  */

/** @defgroup GPIO_LL_EVENTOUT_PIN EVENTOUT Pin
  * @{
  */

#define LL_GPIO_AF_EVENTOUT_PIN_0        AFIO_EVCR_PIN_PX0   /*!< EVENTOUT on pin 0 */
#define LL_GPIO_AF_EVENTOUT_PIN_1        AFIO_EVCR_PIN_PX1   /*!< EVENTOUT on pin 1 */
#define LL_GPIO_AF_EVENTOUT_PIN_2        AFIO_EVCR_PIN_PX2   /*!< EVENTOUT on pin 2 */
#define LL_GPIO_AF_EVENTOUT_PIN_3        AFIO_EVCR_PIN_PX3   /*!< EVENTOUT on pin 3 */
#define LL_GPIO_AF_EVENTOUT_PIN_4        AFIO_EVCR_PIN_PX4   /*!< EVENTOUT on pin 4 */
#define LL_GPIO_AF_EVENTOUT_PIN_5        AFIO_EVCR_PIN_PX5   /*!< EVENTOUT on pin 5 */
#define LL_GPIO_AF_EVENTOUT_PIN_6        AFIO_EVCR_PIN_PX6   /*!< EVENTOUT on pin 6 */
#define LL_GPIO_AF_EVENTOUT_PIN_7        AFIO_EVCR_PIN_PX7   /*!< EVENTOUT on pin 7 */
#define LL_GPIO_AF_EVENTOUT_PIN_8        AFIO_EVCR_PIN_PX8   /*!< EVENTOUT on pin 8 */
#define LL_GPIO_AF_EVENTOUT_PIN_9        AFIO_EVCR_PIN_PX9   /*!< EVENTOUT on pin 9 */
#define LL_GPIO_AF_EVENTOUT_PIN_10       AFIO_EVCR_PIN_PX10  /*!< EVENTOUT on pin 10 */
#define LL_GPIO_AF_EVENTOUT_PIN_11       AFIO_EVCR_PIN_PX11  /*!< EVENTOUT on pin 11 */
#define LL_GPIO_AF_EVENTOUT_PIN_12       AFIO_EVCR_PIN_PX12  /*!< EVENTOUT on pin 12 */
#define LL_GPIO_AF_EVENTOUT_PIN_13       AFIO_EVCR_PIN_PX13  /*!< EVENTOUT on pin 13 */
#define LL_GPIO_AF_EVENTOUT_PIN_14       AFIO_EVCR_PIN_PX14  /*!< EVENTOUT on pin 14 */
#define LL_GPIO_AF_EVENTOUT_PIN_15       AFIO_EVCR_PIN_PX15  /*!< EVENTOUT on pin 15 */

/**
  * @}
  */

/** @defgroup GPIO_LL_EVENTOUT_PORT EVENTOUT Port
  * @{
  */

#define LL_GPIO_AF_EVENTOUT_PORT_A       AFIO_EVCR_PORT_PA  /*!< EVENTOUT on port A */
#define LL_GPIO_AF_EVENTOUT_PORT_B       AFIO_EVCR_PORT_PB  /*!< EVENTOUT on port B */
#define LL_GPIO_AF_EVENTOUT_PORT_C       AFIO_EVCR_PORT_PC  /*!< EVENTOUT on port C */
#define LL_GPIO_AF_EVENTOUT_PORT_D       AFIO_EVCR_PORT_PD  /*!< EVENTOUT on port D */
#define LL_GPIO_AF_EVENTOUT_PORT_E       AFIO_EVCR_PORT_PE  /*!< EVENTOUT on port E */

/**
  * @}
  */

/** @defgroup GPIO_LL_EC_EXTI_PORT GPIO EXTI PORT
  * @{
  */
#define LL_GPIO_AF_EXTI_PORTA            0U   /*!< EXTI PORT A */
#define LL_GPIO_AF_EXTI_PORTB            1U   /*!< EXTI PORT B */
#define LL_GPIO_AF_EXTI_PORTC            2U   /*!< EXTI PORT C */
#define LL_GPIO_AF_EXTI_PORTD            3U   /*!< EXTI PORT D */
#define LL_GPIO_AF_EXTI_PORTE            4U   /*!< EXTI PORT E */
#define LL_GPIO_AF_EXTI_PORTF            5U   /*!< EXTI PORT F */
#define LL_GPIO_AF_EXTI_PORTG            6U   /*!< EXTI PORT G */
/**
  * @}
  */

/** @defgroup GPIO_LL_EC_EXTI_LINE GPIO EXTI LINE
  * @{
  */
#define LL_GPIO_AF_EXTI_LINE0            (0x000FU << 16U | 0U)  /*!< EXTI_POSITION_0  | EXTICR[0] */
#define LL_GPIO_AF_EXTI_LINE1            (0x00F0U << 16U | 0U)  /*!< EXTI_POSITION_4  | EXTICR[0] */
#define LL_GPIO_AF_EXTI_LINE2            (0x0F00U << 16U | 0U)  /*!< EXTI_POSITION_8  | EXTICR[0] */
#define LL_GPIO_AF_EXTI_LINE3            (0xF000U << 16U | 0U)  /*!< EXTI_POSITION_12 | EXTICR[0] */
#define LL_GPIO_AF_EXTI_LINE4            (0x000FU << 16U | 1U)  /*!< EXTI_POSITION_0  | EXTICR[1] */
#define LL_GPIO_AF_EXTI_LINE5            (0x00F0U << 16U | 1U)  /*!< EXTI_POSITION_4  | EXTICR[1] */
#define LL_GPIO_AF_EXTI_LINE6            (0x0F00U << 16U | 1U)  /*!< EXTI_POSITION_8  | EXTICR[1] */
#define LL_GPIO_AF_EXTI_LINE7            (0xF000U << 16U | 1U)  /*!< EXTI_POSITION_12 | EXTICR[1] */
#define LL_GPIO_AF_EXTI_LINE8            (0x000FU << 16U | 2U)  /*!< EXTI_POSITION_0  | EXTICR[2] */
#define LL_GPIO_AF_EXTI_LINE9            (0x00F0U << 16U | 2U)  /*!< EXTI_POSITION_4  | EXTICR[2] */
#define LL_GPIO_AF_EXTI_LINE10           (0x0F00U << 16U | 2U)  /*!< EXTI_POSITION_8  | EXTICR[2] */
#define LL_GPIO_AF_EXTI_LINE11           (0xF000U << 16U | 2U)  /*!< EXTI_POSITION_12 | EXTICR[2] */
#define LL_GPIO_AF_EXTI_LINE12           (0x000FU << 16U | 3U)  /*!< EXTI_POSITION_0  | EXTICR[3] */
#define LL_GPIO_AF_EXTI_LINE13           (0x00F0U << 16U | 3U)  /*!< EXTI_POSITION_4  | EXTICR[3] */
#define LL_GPIO_AF_EXTI_LINE14           (0x0F00U << 16U | 3U)  /*!< EXTI_POSITION_8  | EXTICR[3] */
#define LL_GPIO_AF_EXTI_LINE15           (0xF000U << 16U | 3U)  /*!< EXTI_POSITION_12 | EXTICR[3] */
/**
  * @}
  */

/**
  * @}
  */

/* Exported macro ------------------------------------------------------------*/
/** @defgroup GPIO_LL_Exported_Macros GPIO Exported Macros
  * @{
  */

/** @defgroup GPIO_LL_EM_WRITE_READ Common Write and read registers Macros
  * @{
  */

/**
  * @brief  Write a value in GPIO register
  * @param  __INSTANCE__ GPIO Instance
  * @param  __REG__ Register to be written
  * @param  __VALUE__ Value to be written in the register
  * @retval None
  */
#define LL_GPIO_WriteReg(__INSTANCE__, __REG__, __VALUE__) WRITE_REG(__INSTANCE__->__REG__, (__VALUE__))

/**
  * @brief  Read a value in GPIO register
  * @param  __INSTANCE__ GPIO Instance
  * @param  __REG__ Register to be read
  * @retval Register value
  */
#define LL_GPIO_ReadReg(__INSTANCE__, __REG__) READ_REG(__INSTANCE__->__REG__)
/**
  * @}
  */

/**
  * @}
  */

/* Exported functions --------------------------------------------------------*/
/** @defgroup GPIO_LL_Exported_Functions GPIO Exported Functions
  * @{
  */

/** @defgroup GPIO_LL_EF_Port_Configuration Port Configuration
  * @{
  */

/**
  * @brief  Configure gpio mode for a dedicated pin on dedicated port.
  * @note   I/O mode can be Analog, Floating input, Input with pull-up/pull-down, General purpose Output,
  *         Alternate function Output.
  * @note   Warning: only one pin can be passed as parameter.
  * @rmtoll CRL        CNFy         LL_GPIO_SetPinMode
  * @rmtoll CRL        MODEy        LL_GPIO_SetPinMode
  * @rmtoll CRH        CNFy         LL_GPIO_SetPinMode
  * @rmtoll CRH        MODEy        LL_GPIO_SetPinMode
  * @param  GPIOx GPIO Port
  * @param  Pin This parameter can be one of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  * @param  Mode This parameter can be one of the following values:
  *         @arg @ref LL_GPIO_MODE_ANALOG
  *         @arg @ref LL_GPIO_MODE_FLOATING
  *         @arg @ref LL_GPIO_MODE_INPUT
  *         @arg @ref LL_GPIO_MODE_OUTPUT
  *         @arg @ref LL_GPIO_MODE_ALTERNATE
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_SetPinMode(GPIO_TypeDef *GPIOx, uint32_t Pin, uint32_t Mode)
{
  register uint32_t *pReg = (uint32_t *)((uint32_t)(&GPIOx->CRL) + (Pin >> 24));
  MODIFY_REG(*pReg, ((GPIO_CRL_CNF0 | GPIO_CRL_MODE0) << (POSITION_VAL(Pin) * 4U)), (Mode << (POSITION_VAL(Pin) * 4U)));
}

/**
  * @brief  Return gpio mode for a dedicated pin on dedicated port.
  * @note   I/O mode can be Analog, Floating input, Input with pull-up/pull-down, General purpose Output,
  *         Alternate function Output.
  * @note   Warning: only one pin can be passed as parameter.
  * @rmtoll CRL        CNFy         LL_GPIO_GetPinMode
  * @rmtoll CRL        MODEy        LL_GPIO_GetPinMode
  * @rmtoll CRH        CNFy         LL_GPIO_GetPinMode
  * @rmtoll CRH        MODEy        LL_GPIO_GetPinMode
  * @param  GPIOx GPIO Port
  * @param  Pin This parameter can be one of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  * @retval Returned value can be one of the following values:
  *         @arg @ref LL_GPIO_MODE_ANALOG
  *         @arg @ref LL_GPIO_MODE_FLOATING
  *         @arg @ref LL_GPIO_MODE_INPUT
  *         @arg @ref LL_GPIO_MODE_OUTPUT
  *         @arg @ref LL_GPIO_MODE_ALTERNATE
  */
__STATIC_INLINE uint32_t LL_GPIO_GetPinMode(GPIO_TypeDef *GPIOx, uint32_t Pin)
{
  register uint32_t *pReg = (uint32_t *)((uint32_t)(&GPIOx->CRL) + (Pin >> 24));
  return (READ_BIT(*pReg, ((GPIO_CRL_CNF0 | GPIO_CRL_MODE0) << (POSITION_VAL(Pin) * 4U))) >> (POSITION_VAL(Pin) * 4U));
}

/**
  * @brief  Configure gpio speed for a dedicated pin on dedicated port.
  * @note   I/O speed can be Low, Medium or Fast speed.
  * @note   Warning: only one pin can be passed as parameter.
  * @note   Refer to datasheet for frequency specifications and the power
  *         supply and load conditions for each speed.
  * @rmtoll CRL      MODEy       LL_GPIO_SetPinSpeed
  * @rmtoll CRH      MODEy       LL_GPIO_SetPinSpeed
  * @param  GPIOx GPIO Port
  * @param  Pin This parameter can be one of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  * @param  Speed This parameter can be one of the following values:
  *         @arg @ref LL_GPIO_SPEED_FREQ_LOW
  *         @arg @ref LL_GPIO_SPEED_FREQ_MEDIUM
  *         @arg @ref LL_GPIO_SPEED_FREQ_HIGH
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_SetPinSpeed(GPIO_TypeDef *GPIOx, uint32_t Pin, uint32_t  Speed)
{
  register uint32_t *pReg = (uint32_t *)((uint32_t)(&GPIOx->CRL) + (Pin >> 24));
  MODIFY_REG(*pReg, (GPIO_CRL_MODE0 << (POSITION_VAL(Pin) * 4U)),
             (Speed << (POSITION_VAL(Pin) * 4U)));
}

/**
  * @brief  Return gpio speed for a dedicated pin on dedicated port.
  * @note   I/O speed can be Low, Medium, Fast or High speed.
  * @note   Warning: only one pin can be passed as parameter.
  * @note   Refer to datasheet for frequency specifications and the power
  *         supply and load conditions for each speed.
  * @rmtoll CRL      MODEy       LL_GPIO_GetPinSpeed
  * @rmtoll CRH      MODEy       LL_GPIO_GetPinSpeed
  * @param  GPIOx GPIO Port
  * @param  Pin This parameter can be one of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  * @retval Returned value can be one of the following values:
  *         @arg @ref LL_GPIO_SPEED_FREQ_LOW
  *         @arg @ref LL_GPIO_SPEED_FREQ_MEDIUM
  *         @arg @ref LL_GPIO_SPEED_FREQ_HIGH
  */
__STATIC_INLINE uint32_t LL_GPIO_GetPinSpeed(GPIO_TypeDef *GPIOx, uint32_t Pin)
{
  register uint32_t *pReg = (uint32_t *)((uint32_t)(&GPIOx->CRL) + (Pin >> 24));
  return (READ_BIT(*pReg, (GPIO_CRL_MODE0 << (POSITION_VAL(Pin) * 4U))) >> (POSITION_VAL(Pin) * 4U));
}

/**
  * @brief  Configure gpio output type for several pins on dedicated port.
  * @note   Output type as to be set when gpio pin is in output or
  *         alternate modes. Possible type are Push-pull or Open-drain.
  * @rmtoll CRL       MODEy           LL_GPIO_SetPinOutputType
  * @rmtoll CRH       MODEy           LL_GPIO_SetPinOutputType
  * @param  GPIOx GPIO Port
  * @param  Pin This parameter can be a combination of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  *         @arg @ref LL_GPIO_PIN_ALL
  * @param  OutputType This parameter can be one of the following values:
  *         @arg @ref LL_GPIO_OUTPUT_PUSHPULL
  *         @arg @ref LL_GPIO_OUTPUT_OPENDRAIN
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_SetPinOutputType(GPIO_TypeDef *GPIOx, uint32_t Pin, uint32_t OutputType)
{
  register uint32_t *pReg = (uint32_t *)((uint32_t)(&GPIOx->CRL) + (Pin >> 24));
  MODIFY_REG(*pReg, (GPIO_CRL_CNF0_0 << (POSITION_VAL(Pin) * 4U)),
             (OutputType << (POSITION_VAL(Pin) * 4U)));
}

/**
  * @brief  Return gpio output type for several pins on dedicated port.
  * @note   Output type as to be set when gpio pin is in output or
  *         alternate modes. Possible type are Push-pull or Open-drain.
  * @note   Warning: only one pin can be passed as parameter.
  * @rmtoll CRL       MODEy       LL_GPIO_GetPinOutputType
  * @rmtoll CRH       MODEy       LL_GPIO_GetPinOutputType
  * @param  GPIOx GPIO Port
  * @param  Pin This parameter can be one of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  *         @arg @ref LL_GPIO_PIN_ALL
  * @retval Returned value can be one of the following values:
  *         @arg @ref LL_GPIO_OUTPUT_PUSHPULL
  *         @arg @ref LL_GPIO_OUTPUT_OPENDRAIN
  */
__STATIC_INLINE uint32_t LL_GPIO_GetPinOutputType(GPIO_TypeDef *GPIOx, uint32_t Pin)
{
  register uint32_t *pReg = (uint32_t *)((uint32_t)(&GPIOx->CRL) + (Pin >> 24));
  return (READ_BIT(*pReg, (GPIO_CRL_CNF0_0 << (POSITION_VAL(Pin) * 4U))) >> (POSITION_VAL(Pin) * 4U));

}

/**
  * @brief  Configure gpio pull-up or pull-down for a dedicated pin on a dedicated port.
  * @note   Warning: only one pin can be passed as parameter.
  * @rmtoll ODR        ODR         LL_GPIO_SetPinPull
  * @param  GPIOx GPIO Port
  * @param  Pin This parameter can be one of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  * @param  Pull This parameter can be one of the following values:
  *         @arg @ref LL_GPIO_PULL_DOWN
  *         @arg @ref LL_GPIO_PULL_UP
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_SetPinPull(GPIO_TypeDef *GPIOx, uint32_t Pin, uint32_t Pull)
{
  MODIFY_REG(GPIOx->ODR, (Pin >> GPIO_PIN_MASK_POS), Pull << (POSITION_VAL(Pin >> GPIO_PIN_MASK_POS)));
}

/**
  * @brief  Return gpio pull-up or pull-down for a dedicated pin on a dedicated port
  * @note   Warning: only one pin can be passed as parameter.
  * @rmtoll ODR        ODR         LL_GPIO_GetPinPull
  * @param  GPIOx GPIO Port
  * @param  Pin This parameter can be one of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  * @retval Returned value can be one of the following values:
  *         @arg @ref LL_GPIO_PULL_DOWN
  *         @arg @ref LL_GPIO_PULL_UP
  */
__STATIC_INLINE uint32_t LL_GPIO_GetPinPull(GPIO_TypeDef *GPIOx, uint32_t Pin)
{
  return (READ_BIT(GPIOx->ODR, (GPIO_ODR_ODR0 << (POSITION_VAL(Pin >> GPIO_PIN_MASK_POS)))) >> (POSITION_VAL(Pin >> GPIO_PIN_MASK_POS)));
}

/**
  * @brief  Lock configuration of several pins for a dedicated port.
  * @note   When the lock sequence has been applied on a port bit, the
  *         value of this port bit can no longer be modified until the
  *         next reset.
  * @note   Each lock bit freezes a specific configuration register
  *         (control and alternate function registers).
  * @rmtoll LCKR         LCKK          LL_GPIO_LockPin
  * @param  GPIOx GPIO Port
  * @param  PinMask This parameter can be a combination of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  *         @arg @ref LL_GPIO_PIN_ALL
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_LockPin(GPIO_TypeDef *GPIOx, uint32_t PinMask)
{
  __IO uint32_t temp;
  WRITE_REG(GPIOx->LCKR, GPIO_LCKR_LCKK | ((PinMask >> GPIO_PIN_MASK_POS) & 0x0000FFFFU));
  WRITE_REG(GPIOx->LCKR, ((PinMask >> GPIO_PIN_MASK_POS) & 0x0000FFFFU));
  WRITE_REG(GPIOx->LCKR, GPIO_LCKR_LCKK | ((PinMask >> GPIO_PIN_MASK_POS) & 0x0000FFFFU));
  temp = READ_REG(GPIOx->LCKR);
  (void) temp;
}

/**
  * @brief  Return 1 if all pins passed as parameter, of a dedicated port, are locked. else Return 0.
  * @rmtoll LCKR         LCKy          LL_GPIO_IsPinLocked
  * @param  GPIOx GPIO Port
  * @param  PinMask This parameter can be a combination of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  *         @arg @ref LL_GPIO_PIN_ALL
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_IsPinLocked(GPIO_TypeDef *GPIOx, uint32_t PinMask)
{
  return (READ_BIT(GPIOx->LCKR, ((PinMask >> GPIO_PIN_MASK_POS) & 0x0000FFFFU)) == ((PinMask >> GPIO_PIN_MASK_POS) & 0x0000FFFFU));
}

/**
  * @brief  Return 1 if one of the pin of a dedicated port is locked. else return 0.
  * @rmtoll LCKR         LCKK          LL_GPIO_IsAnyPinLocked
  * @param  GPIOx GPIO Port
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_IsAnyPinLocked(GPIO_TypeDef *GPIOx)
{
  return (READ_BIT(GPIOx->LCKR, GPIO_LCKR_LCKK) == (GPIO_LCKR_LCKK));
}

/**
  * @}
  */

/** @defgroup GPIO_LL_EF_Data_Access Data Access
  * @{
  */

/**
  * @brief  Return full input data register value for a dedicated port.
  * @rmtoll IDR          IDy           LL_GPIO_ReadInputPort
  * @param  GPIOx GPIO Port
  * @retval Input data register value of port
  */
__STATIC_INLINE uint32_t LL_GPIO_ReadInputPort(GPIO_TypeDef *GPIOx)
{
  return (READ_REG(GPIOx->IDR));
}

/**
  * @brief  Return if input data level for several pins of dedicated port is high or low.
  * @rmtoll IDR          IDy           LL_GPIO_IsInputPinSet
  * @param  GPIOx GPIO Port
  * @param  PinMask This parameter can be a combination of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  *         @arg @ref LL_GPIO_PIN_ALL
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_IsInputPinSet(GPIO_TypeDef *GPIOx, uint32_t PinMask)
{
  return (READ_BIT(GPIOx->IDR, (PinMask >> GPIO_PIN_MASK_POS) & 0x0000FFFFU) == ((PinMask >> GPIO_PIN_MASK_POS) & 0x0000FFFFU));
}

/**
  * @brief  Write output data register for the port.
  * @rmtoll ODR          ODy           LL_GPIO_WriteOutputPort
  * @param  GPIOx GPIO Port
  * @param  PortValue Level value for each pin of the port
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_WriteOutputPort(GPIO_TypeDef *GPIOx, uint32_t PortValue)
{
  WRITE_REG(GPIOx->ODR, PortValue);
}

/**
  * @brief  Return full output data register value for a dedicated port.
  * @rmtoll ODR          ODy           LL_GPIO_ReadOutputPort
  * @param  GPIOx GPIO Port
  * @retval Output data register value of port
  */
__STATIC_INLINE uint32_t LL_GPIO_ReadOutputPort(GPIO_TypeDef *GPIOx)
{
  return (uint32_t)(READ_REG(GPIOx->ODR));
}

/**
  * @brief  Return if input data level for several pins of dedicated port is high or low.
  * @rmtoll ODR          ODy           LL_GPIO_IsOutputPinSet
  * @param  GPIOx GPIO Port
  * @param  PinMask This parameter can be a combination of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  *         @arg @ref LL_GPIO_PIN_ALL
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_IsOutputPinSet(GPIO_TypeDef *GPIOx, uint32_t PinMask)
{
  return (READ_BIT(GPIOx->ODR, (PinMask >> GPIO_PIN_MASK_POS) & 0x0000FFFFU) == ((PinMask >> GPIO_PIN_MASK_POS) & 0x0000FFFFU));
}

/**
  * @brief  Set several pins to high level on dedicated gpio port.
  * @rmtoll BSRR         BSy           LL_GPIO_SetOutputPin
  * @param  GPIOx GPIO Port
  * @param  PinMask This parameter can be a combination of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  *         @arg @ref LL_GPIO_PIN_ALL
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_SetOutputPin(GPIO_TypeDef *GPIOx, uint32_t PinMask)
{
  WRITE_REG(GPIOx->BSRR, (PinMask >> GPIO_PIN_MASK_POS) & 0x0000FFFFU);
}

/**
  * @brief  Set several pins to low level on dedicated gpio port.
  * @rmtoll BRR          BRy           LL_GPIO_ResetOutputPin
  * @param  GPIOx GPIO Port
  * @param  PinMask This parameter can be a combination of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  *         @arg @ref LL_GPIO_PIN_ALL
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_ResetOutputPin(GPIO_TypeDef *GPIOx, uint32_t PinMask)
{
  WRITE_REG(GPIOx->BRR, (PinMask >> GPIO_PIN_MASK_POS) & 0x0000FFFFU);
}

/**
  * @brief  Toggle data value for several pin of dedicated port.
  * @rmtoll ODR          ODy           LL_GPIO_TogglePin
  * @param  GPIOx GPIO Port
  * @param  PinMask This parameter can be a combination of the following values:
  *         @arg @ref LL_GPIO_PIN_0
  *         @arg @ref LL_GPIO_PIN_1
  *         @arg @ref LL_GPIO_PIN_2
  *         @arg @ref LL_GPIO_PIN_3
  *         @arg @ref LL_GPIO_PIN_4
  *         @arg @ref LL_GPIO_PIN_5
  *         @arg @ref LL_GPIO_PIN_6
  *         @arg @ref LL_GPIO_PIN_7
  *         @arg @ref LL_GPIO_PIN_8
  *         @arg @ref LL_GPIO_PIN_9
  *         @arg @ref LL_GPIO_PIN_10
  *         @arg @ref LL_GPIO_PIN_11
  *         @arg @ref LL_GPIO_PIN_12
  *         @arg @ref LL_GPIO_PIN_13
  *         @arg @ref LL_GPIO_PIN_14
  *         @arg @ref LL_GPIO_PIN_15
  *         @arg @ref LL_GPIO_PIN_ALL
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_TogglePin(GPIO_TypeDef *GPIOx, uint32_t PinMask)
{
  WRITE_REG(GPIOx->ODR, READ_REG(GPIOx->ODR) ^ ((PinMask >> GPIO_PIN_MASK_POS) & 0x0000FFFFU));
}

/**
  * @}
  */

/** @defgroup GPIO_AF_REMAPPING Alternate Function Remapping
  * @brief This section propose definition to remap the alternate function to some other port/pins.
  * @{
  */

/**
  * @brief  Enable the remapping of SPI1 alternate function NSS, SCK, MISO and MOSI.
  * @rmtoll MAPR          SPI1_REMAP           LL_GPIO_AF_EnableRemap_SPI1
  * @note   ENABLE: Remap (NSS/PA15, SCK/PB3, MISO/PB4, MOSI/PB5)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_SPI1(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_SPI1_REMAP | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Disable the remapping of SPI1 alternate function NSS, SCK, MISO and MOSI.
  * @rmtoll MAPR          SPI1_REMAP           LL_GPIO_AF_DisableRemap_SPI1
  * @note  DISABLE: No remap (NSS/PA4,  SCK/PA5, MISO/PA6, MOSI/PA7)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_SPI1(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_SPI1_REMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief  Check if SPI1 has been remaped or not
  * @rmtoll MAPR         SPI1_REMAP         LL_GPIO_AF_IsEnabledRemap_SPI1
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_SPI1(void)
{
  return (READ_BIT(AFIO->MAPR, AFIO_MAPR_SPI1_REMAP) == (AFIO_MAPR_SPI1_REMAP));
}

/**
  * @brief Enable the remapping of I2C1 alternate function SCL and SDA.
  * @rmtoll MAPR          I2C1_REMAP           LL_GPIO_AF_EnableRemap_I2C1
  * @note  ENABLE: Remap     (SCL/PB8, SDA/PB9)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_I2C1(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_I2C1_REMAP | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Disable the remapping of I2C1 alternate function SCL and SDA.
  * @rmtoll MAPR          I2C1_REMAP           LL_GPIO_AF_DisableRemap_I2C1
  * @note  DISABLE: No remap (SCL/PB6, SDA/PB7)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_I2C1(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_I2C1_REMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief  Check if I2C1 has been remaped or not
  * @rmtoll MAPR         I2C1_REMAP         LL_GPIO_AF_IsEnabledRemap_I2C1
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_I2C1(void)
{
  return (READ_BIT(AFIO->MAPR, AFIO_MAPR_I2C1_REMAP) == (AFIO_MAPR_I2C1_REMAP));
}

/**
  * @brief Enable the remapping of USART1 alternate function TX and RX.
  * @rmtoll MAPR          USART1_REMAP           LL_GPIO_AF_EnableRemap_USART1
  * @note  ENABLE: Remap     (TX/PB6, RX/PB7)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_USART1(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_USART1_REMAP | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Disable the remapping of USART1 alternate function TX and RX.
  * @rmtoll MAPR          USART1_REMAP           LL_GPIO_AF_DisableRemap_USART1
  * @note  DISABLE: No remap (TX/PA9, RX/PA10)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_USART1(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_USART1_REMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief  Check if USART1 has been remaped or not
  * @rmtoll MAPR         USART1_REMAP         LL_GPIO_AF_IsEnabledRemap_USART1
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_USART1(void)
{
  return (READ_BIT(AFIO->MAPR, AFIO_MAPR_USART1_REMAP) == (AFIO_MAPR_USART1_REMAP));
}

/**
  * @brief Enable the remapping of USART2 alternate function CTS, RTS, CK, TX and RX.
  * @rmtoll MAPR          USART2_REMAP           LL_GPIO_AF_EnableRemap_USART2
  * @note  ENABLE: Remap     (CTS/PD3, RTS/PD4, TX/PD5, RX/PD6, CK/PD7)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_USART2(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_USART2_REMAP | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Disable the remapping of USART2 alternate function CTS, RTS, CK, TX and RX.
  * @rmtoll MAPR          USART2_REMAP           LL_GPIO_AF_DisableRemap_USART2
  * @note  DISABLE: No remap (CTS/PA0, RTS/PA1, TX/PA2, RX/PA3, CK/PA4)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_USART2(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_USART2_REMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief  Check if USART2 has been remaped or not
  * @rmtoll MAPR         USART2_REMAP         LL_GPIO_AF_IsEnabledRemap_USART2
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_USART2(void)
{
  return (READ_BIT(AFIO->MAPR, AFIO_MAPR_USART2_REMAP) == (AFIO_MAPR_USART2_REMAP));
}

#if defined (AFIO_MAPR_USART3_REMAP)
/**
  * @brief Enable the remapping of USART3 alternate function CTS, RTS, CK, TX and RX.
  * @rmtoll MAPR          USART3_REMAP           LL_GPIO_AF_EnableRemap_USART3
  * @note  ENABLE: Full remap     (TX/PD8,  RX/PD9,  CK/PD10, CTS/PD11, RTS/PD12)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_USART3(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_USART3_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_USART3_REMAP_FULLREMAP | AFIO_MAPR_SWJ_CFG));
}

/**
  * @brief Enable the remapping of USART3 alternate function CTS, RTS, CK, TX and RX.
  * @rmtoll MAPR          USART3_REMAP           LL_GPIO_AF_RemapPartial_USART3
  * @note  PARTIAL: Partial remap (TX/PC10, RX/PC11, CK/PC12, CTS/PB13, RTS/PB14)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_RemapPartial_USART3(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_USART3_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_USART3_REMAP_PARTIALREMAP | AFIO_MAPR_SWJ_CFG));
}

/**
  * @brief Disable the remapping of USART3 alternate function CTS, RTS, CK, TX and RX.
  * @rmtoll MAPR          USART3_REMAP           LL_GPIO_AF_DisableRemap_USART3
  * @note  DISABLE: No remap      (TX/PB10, RX/PB11, CK/PB12, CTS/PB13, RTS/PB14)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_USART3(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_USART3_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_USART3_REMAP_NOREMAP | AFIO_MAPR_SWJ_CFG));
}
#endif

/**
  * @brief Enable the remapping of TIM1 alternate function channels 1 to 4, 1N to 3N, external trigger (ETR) and Break input (BKIN)
  * @rmtoll MAPR          TIM1_REMAP           LL_GPIO_AF_EnableRemap_TIM1
  * @note  ENABLE: Full remap     (ETR/PE7,  CH1/PE9, CH2/PE11, CH3/PE13, CH4/PE14, BKIN/PE15, CH1N/PE8,  CH2N/PE10, CH3N/PE12)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM1(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_TIM1_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_TIM1_REMAP_FULLREMAP | AFIO_MAPR_SWJ_CFG));
}

/**
  * @brief Enable the remapping of TIM1 alternate function channels 1 to 4, 1N to 3N, external trigger (ETR) and Break input (BKIN)
  * @rmtoll MAPR          TIM1_REMAP           LL_GPIO_AF_RemapPartial_TIM1
  * @note  PARTIAL: Partial remap (ETR/PA12, CH1/PA8, CH2/PA9,  CH3/PA10, CH4/PA11, BKIN/PA6,  CH1N/PA7,  CH2N/PB0,  CH3N/PB1)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_RemapPartial_TIM1(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_TIM1_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_TIM1_REMAP_PARTIALREMAP | AFIO_MAPR_SWJ_CFG));
}

/**
  * @brief Disable the remapping of TIM1 alternate function channels 1 to 4, 1N to 3N, external trigger (ETR) and Break input (BKIN)
  * @rmtoll MAPR          TIM1_REMAP           LL_GPIO_AF_DisableRemap_TIM1
  * @note  DISABLE: No remap      (ETR/PA12, CH1/PA8, CH2/PA9,  CH3/PA10, CH4/PA11, BKIN/PB12, CH1N/PB13, CH2N/PB14, CH3N/PB15)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM1(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_TIM1_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_TIM1_REMAP_NOREMAP | AFIO_MAPR_SWJ_CFG));
}

/**
  * @brief Enable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR)
  * @rmtoll MAPR          TIM2_REMAP           LL_GPIO_AF_EnableRemap_TIM2
  * @note  ENABLE: Full remap       (CH1/ETR/PA15, CH2/PB3, CH3/PB10, CH4/PB11)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM2(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_TIM2_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_TIM2_REMAP_FULLREMAP | AFIO_MAPR_SWJ_CFG));
}

/**
  * @brief Enable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR)
  * @rmtoll MAPR          TIM2_REMAP           LL_GPIO_AF_RemapPartial2_TIM2
  * @note  PARTIAL_2: Partial remap (CH1/ETR/PA0,  CH2/PA1, CH3/PB10, CH4/PB11)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_RemapPartial2_TIM2(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_TIM2_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_TIM2_REMAP_PARTIALREMAP2 | AFIO_MAPR_SWJ_CFG));
}

/**
  * @brief Enable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR)
  * @rmtoll MAPR          TIM2_REMAP           LL_GPIO_AF_RemapPartial1_TIM2
  * @note  PARTIAL_1: Partial remap (CH1/ETR/PA15, CH2/PB3, CH3/PA2,  CH4/PA3)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_RemapPartial1_TIM2(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_TIM2_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_TIM2_REMAP_PARTIALREMAP1 | AFIO_MAPR_SWJ_CFG));
}

/**
  * @brief Disable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR)
  * @rmtoll MAPR          TIM2_REMAP           LL_GPIO_AF_DisableRemap_TIM2
  * @note  DISABLE: No remap        (CH1/ETR/PA0,  CH2/PA1, CH3/PA2,  CH4/PA3)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM2(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_TIM2_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_TIM2_REMAP_NOREMAP | AFIO_MAPR_SWJ_CFG));
}

/**
  * @brief Enable the remapping of TIM3 alternate function channels 1 to 4
  * @rmtoll MAPR          TIM3_REMAP           LL_GPIO_AF_EnableRemap_TIM3
  * @note  ENABLE: Full remap     (CH1/PC6, CH2/PC7, CH3/PC8, CH4/PC9)
  * @note  TIM3_ETR on PE0 is not re-mapped.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM3(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_TIM3_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_TIM3_REMAP_FULLREMAP | AFIO_MAPR_SWJ_CFG));
}

/**
  * @brief Enable the remapping of TIM3 alternate function channels 1 to 4
  * @rmtoll MAPR          TIM3_REMAP           LL_GPIO_AF_RemapPartial_TIM3
  * @note  PARTIAL: Partial remap (CH1/PB4, CH2/PB5, CH3/PB0, CH4/PB1)
  * @note  TIM3_ETR on PE0 is not re-mapped.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_RemapPartial_TIM3(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_TIM3_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_TIM3_REMAP_PARTIALREMAP | AFIO_MAPR_SWJ_CFG));
}

/**
  * @brief Disable the remapping of TIM3 alternate function channels 1 to 4
  * @rmtoll MAPR          TIM3_REMAP           LL_GPIO_AF_DisableRemap_TIM3
  * @note  DISABLE: No remap      (CH1/PA6, CH2/PA7, CH3/PB0, CH4/PB1)
  * @note  TIM3_ETR on PE0 is not re-mapped.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM3(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_TIM3_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_TIM3_REMAP_NOREMAP | AFIO_MAPR_SWJ_CFG));
}

#if defined(AFIO_MAPR_TIM4_REMAP)
/**
  * @brief Enable the remapping of TIM4 alternate function channels 1 to 4.
  * @rmtoll MAPR          TIM4_REMAP           LL_GPIO_AF_EnableRemap_TIM4
  * @note  ENABLE: Full remap (TIM4_CH1/PD12, TIM4_CH2/PD13, TIM4_CH3/PD14, TIM4_CH4/PD15)
  * @note  TIM4_ETR on PE0 is not re-mapped.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM4(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_TIM4_REMAP | AFIO_MAPR_SWJ_CFG);
}
/**
  * @brief Disable the remapping of TIM4 alternate function channels 1 to 4.
  * @rmtoll MAPR          TIM4_REMAP           LL_GPIO_AF_DisableRemap_TIM4
  * @note  DISABLE: No remap  (TIM4_CH1/PB6,  TIM4_CH2/PB7,  TIM4_CH3/PB8,  TIM4_CH4/PB9)
  * @note  TIM4_ETR on PE0 is not re-mapped.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM4(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_TIM4_REMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief  Check if TIM4 has been remaped or not
  * @rmtoll MAPR         TIM4_REMAP         LL_GPIO_AF_IsEnabledRemap_TIM4
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_TIM4(void)
{
  return (READ_BIT(AFIO->MAPR, AFIO_MAPR_TIM4_REMAP) == (AFIO_MAPR_TIM4_REMAP));
}
#endif

#if defined(AFIO_MAPR_CAN_REMAP_REMAP1)

/**
  * @brief Enable or disable the remapping of CAN alternate function CAN_RX and CAN_TX in devices with a single CAN interface.
  * @rmtoll MAPR          CAN_REMAP           LL_GPIO_AF_RemapPartial1_CAN1
  * @note  CASE 1: CAN_RX mapped to PA11, CAN_TX mapped to PA12
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_RemapPartial1_CAN1(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_CAN_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_CAN_REMAP_REMAP1 | AFIO_MAPR_SWJ_CFG));
}

/**
  * @brief Enable or disable the remapping of CAN alternate function CAN_RX and CAN_TX in devices with a single CAN interface.
  * @rmtoll MAPR          CAN_REMAP           LL_GPIO_AF_RemapPartial2_CAN1
  * @note  CASE 2: CAN_RX mapped to PB8,  CAN_TX mapped to PB9 (not available on 36-pin package)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_RemapPartial2_CAN1(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_CAN_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_CAN_REMAP_REMAP2 | AFIO_MAPR_SWJ_CFG));
}

/**
  * @brief Enable or disable the remapping of CAN alternate function CAN_RX and CAN_TX in devices with a single CAN interface.
  * @rmtoll MAPR          CAN_REMAP           LL_GPIO_AF_RemapPartial3_CAN1
  * @note  CASE 3: CAN_RX mapped to PD0,  CAN_TX mapped to PD1
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_RemapPartial3_CAN1(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_CAN_REMAP | AFIO_MAPR_SWJ_CFG), (AFIO_MAPR_CAN_REMAP_REMAP3 | AFIO_MAPR_SWJ_CFG));
}
#endif

/**
  * @brief Enable the remapping of PD0 and PD1. When the HSE oscillator is not used
  *        (application running on internal 8 MHz RC) PD0 and PD1 can be mapped on OSC_IN and
  *        OSC_OUT. This is available only on 36, 48 and 64 pins packages (PD0 and PD1 are available
  *        on 100-pin and 144-pin packages, no need for remapping).
  * @rmtoll MAPR          PD01_REMAP           LL_GPIO_AF_EnableRemap_PD01
  * @note  ENABLE: PD0 remapped on OSC_IN, PD1 remapped on OSC_OUT.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_PD01(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_PD01_REMAP | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Disable the remapping of PD0 and PD1. When the HSE oscillator is not used
  *        (application running on internal 8 MHz RC) PD0 and PD1 can be mapped on OSC_IN and
  *        OSC_OUT. This is available only on 36, 48 and 64 pins packages (PD0 and PD1 are available
  *        on 100-pin and 144-pin packages, no need for remapping).
  * @rmtoll MAPR          PD01_REMAP           LL_GPIO_AF_DisableRemap_PD01
  * @note  DISABLE: No remapping of PD0 and PD1
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_PD01(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_PD01_REMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief  Check if PD01 has been remaped or not
  * @rmtoll MAPR         PD01_REMAP         LL_GPIO_AF_IsEnabledRemap_PD01
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_PD01(void)
{
  return (READ_BIT(AFIO->MAPR, AFIO_MAPR_PD01_REMAP) == (AFIO_MAPR_PD01_REMAP));
}

#if defined(AFIO_MAPR_TIM5CH4_IREMAP)
/**
  * @brief Enable the remapping of TIM5CH4.
  * @rmtoll MAPR          TIM5CH4_IREMAP           LL_GPIO_AF_EnableRemap_TIM5CH4
  * @note  ENABLE: LSI internal clock is connected to TIM5_CH4 input for calibration purpose.
  * @note  This function is available only in high density value line devices.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM5CH4(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_TIM5CH4_IREMAP | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Disable the remapping of TIM5CH4.
  * @rmtoll MAPR          TIM5CH4_IREMAP           LL_GPIO_AF_DisableRemap_TIM5CH4
  * @note  DISABLE: TIM5_CH4 is connected to PA3
  * @note  This function is available only in high density value line devices.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM5CH4(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_TIM5CH4_IREMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief  Check if TIM5CH4 has been remaped or not
  * @rmtoll MAPR         TIM5CH4_IREMAP         LL_GPIO_AF_IsEnabledRemap_TIM5CH4
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_TIM5CH4(void)
{
  return (READ_BIT(AFIO->MAPR, AFIO_MAPR_TIM5CH4_IREMAP) == (AFIO_MAPR_TIM5CH4_IREMAP));
}
#endif

#if defined(AFIO_MAPR_ETH_REMAP)
/**
  * @brief Enable the remapping of Ethernet MAC connections with the PHY.
  * @rmtoll MAPR          ETH_REMAP           LL_GPIO_AF_EnableRemap_ETH
  * @note  ENABLE: Remap     (RX_DV-CRS_DV/PD8, RXD0/PD9, RXD1/PD10, RXD2/PD11, RXD3/PD12)
  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_ETH(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_ETH_REMAP | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Disable the remapping of Ethernet MAC connections with the PHY.
  * @rmtoll MAPR          ETH_REMAP           LL_GPIO_AF_DisableRemap_ETH
  * @note  DISABLE: No remap (RX_DV-CRS_DV/PA7, RXD0/PC4, RXD1/PC5,  RXD2/PB0,  RXD3/PB1)
  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_ETH(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_ETH_REMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief  Check if ETH has been remaped or not
  * @rmtoll MAPR         ETH_REMAP         LL_GPIO_AF_IsEnabledRemap_ETH
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_ETH(void)
{
  return (READ_BIT(AFIO->MAPR, AFIO_MAPR_ETH_REMAP) == (AFIO_MAPR_ETH_REMAP));
}
#endif

#if defined(AFIO_MAPR_CAN2_REMAP)

/**
  * @brief Enable the remapping of CAN2 alternate function CAN2_RX and CAN2_TX.
  * @rmtoll MAPR          CAN2_REMAP           LL_GPIO_AF_EnableRemap_CAN2
  * @note  ENABLE: Remap     (CAN2_RX/PB5,  CAN2_TX/PB6)
  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_CAN2(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_CAN2_REMAP | AFIO_MAPR_SWJ_CFG);
}
/**
  * @brief Disable the remapping of CAN2 alternate function CAN2_RX and CAN2_TX.
  * @rmtoll MAPR          CAN2_REMAP           LL_GPIO_AF_DisableRemap_CAN2
  * @note  DISABLE: No remap (CAN2_RX/PB12, CAN2_TX/PB13)
  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_CAN2(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_CAN2_REMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief  Check if CAN2 has been remaped or not
  * @rmtoll MAPR         CAN2_REMAP         LL_GPIO_AF_IsEnabledRemap_CAN2
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_CAN2(void)
{
  return (READ_BIT(AFIO->MAPR, AFIO_MAPR_CAN2_REMAP) == (AFIO_MAPR_CAN2_REMAP));
}
#endif

#if defined(AFIO_MAPR_MII_RMII_SEL)
/**
  * @brief Configures the Ethernet MAC internally for use with an external MII or RMII PHY.
  * @rmtoll MAPR          MII_RMII_SEL           LL_GPIO_AF_Select_ETH_RMII
  * @note  ETH_RMII: Configure Ethernet MAC for connection with an RMII PHY
  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_Select_ETH_RMII(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_MII_RMII_SEL | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Configures the Ethernet MAC internally for use with an external MII or RMII PHY.
  * @rmtoll MAPR          MII_RMII_SEL           LL_GPIO_AF_Select_ETH_MII
  * @note  ETH_MII: Configure Ethernet MAC for connection with an MII PHY
  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_Select_ETH_MII(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_MII_RMII_SEL | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}
#endif

#if defined(AFIO_MAPR_ADC1_ETRGINJ_REMAP)
/**
  * @brief Enable the remapping of ADC1_ETRGINJ (ADC 1 External trigger injected conversion).
  * @rmtoll MAPR          ADC1_ETRGINJ_REMAP           LL_GPIO_AF_EnableRemap_ADC1_ETRGINJ
  * @note  ENABLE: ADC1 External Event injected conversion is connected to TIM8 Channel4.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_ADC1_ETRGINJ(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_ADC1_ETRGINJ_REMAP | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Disable the remapping of ADC1_ETRGINJ (ADC 1 External trigger injected conversion).
  * @rmtoll MAPR          ADC1_ETRGINJ_REMAP           LL_GPIO_AF_DisableRemap_ADC1_ETRGINJ
  * @note  DISABLE: ADC1 External trigger injected conversion is connected to EXTI15
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_ADC1_ETRGINJ(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_ADC1_ETRGINJ_REMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief  Check if ADC1_ETRGINJ has been remaped or not
  * @rmtoll MAPR         ADC1_ETRGINJ_REMAP         LL_GPIO_AF_IsEnabledRemap_ADC1_ETRGINJ
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_ADC1_ETRGINJ(void)
{
  return (READ_BIT(AFIO->MAPR, AFIO_MAPR_ADC1_ETRGINJ_REMAP) == (AFIO_MAPR_ADC1_ETRGINJ_REMAP));
}
#endif

#if defined(AFIO_MAPR_ADC1_ETRGREG_REMAP)
/**
  * @brief Enable the remapping of ADC1_ETRGREG (ADC 1 External trigger regular conversion).
  * @rmtoll MAPR          ADC1_ETRGREG_REMAP           LL_GPIO_AF_EnableRemap_ADC1_ETRGREG
  * @note  ENABLE: ADC1 External Event regular conversion is connected to TIM8 TRG0.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_ADC1_ETRGREG(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_ADC1_ETRGREG_REMAP | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Disable the remapping of ADC1_ETRGREG (ADC 1 External trigger regular conversion).
  * @rmtoll MAPR          ADC1_ETRGREG_REMAP           LL_GPIO_AF_DisableRemap_ADC1_ETRGREG
  * @note  DISABLE: ADC1 External trigger regular conversion is connected to EXTI11
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_ADC1_ETRGREG(void)
{
   MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_ADC1_ETRGREG_REMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief  Check if ADC1_ETRGREG has been remaped or not
  * @rmtoll MAPR         ADC1_ETRGREG_REMAP         LL_GPIO_AF_IsEnabledRemap_ADC1_ETRGREG
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_ADC1_ETRGREG(void)
{
  return (READ_BIT(AFIO->MAPR, AFIO_MAPR_ADC1_ETRGREG_REMAP) == (AFIO_MAPR_ADC1_ETRGREG_REMAP));
}
#endif

#if defined(AFIO_MAPR_ADC2_ETRGINJ_REMAP)

/**
  * @brief Enable the remapping of ADC2_ETRGREG (ADC 2 External trigger injected conversion).
  * @rmtoll MAPR          ADC2_ETRGINJ_REMAP           LL_GPIO_AF_EnableRemap_ADC2_ETRGINJ
  * @note  ENABLE: ADC2 External Event injected conversion is connected to TIM8 Channel4.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_ADC2_ETRGINJ(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_ADC2_ETRGINJ_REMAP | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Disable the remapping of ADC2_ETRGREG (ADC 2 External trigger injected conversion).
  * @rmtoll MAPR          ADC2_ETRGINJ_REMAP           LL_GPIO_AF_DisableRemap_ADC2_ETRGINJ
  * @note  DISABLE: ADC2 External trigger injected conversion is connected to EXTI15
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_ADC2_ETRGINJ(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_ADC2_ETRGINJ_REMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief  Check if ADC2_ETRGINJ has been remaped or not
  * @rmtoll MAPR         ADC2_ETRGINJ_REMAP         LL_GPIO_AF_IsEnabledRemap_ADC2_ETRGINJ
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_ADC2_ETRGINJ(void)
{
  return (READ_BIT(AFIO->MAPR, AFIO_MAPR_ADC2_ETRGINJ_REMAP) == (AFIO_MAPR_ADC2_ETRGINJ_REMAP));
}
#endif

#if defined (AFIO_MAPR_ADC2_ETRGREG_REMAP)

/**
  * @brief Enable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion).
  * @rmtoll MAPR          ADC2_ETRGREG_REMAP           LL_GPIO_AF_EnableRemap_ADC2_ETRGREG
  * @note  ENABLE: ADC2 External Event regular conversion is connected to TIM8 TRG0.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_ADC2_ETRGREG(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_ADC2_ETRGREG_REMAP | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Disable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion).
  * @rmtoll MAPR          ADC2_ETRGREG_REMAP           LL_GPIO_AF_DisableRemap_ADC2_ETRGREG
  * @note  DISABLE: ADC2 External trigger regular conversion is connected to EXTI11
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_ADC2_ETRGREG(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_ADC2_ETRGREG_REMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief  Check if ADC2_ETRGREG has been remaped or not
  * @rmtoll MAPR         ADC2_ETRGREG_REMAP         LL_GPIO_AF_IsEnabledRemap_ADC2_ETRGREG
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_ADC2_ETRGREG(void)
{
  return (READ_BIT(AFIO->MAPR, AFIO_MAPR_ADC2_ETRGREG_REMAP) == (AFIO_MAPR_ADC2_ETRGREG_REMAP));
}
#endif

/**
  * @brief Enable the Serial wire JTAG configuration
  * @rmtoll MAPR          SWJ_CFG           LL_GPIO_AF_EnableRemap_SWJ
  * @note  ENABLE: Full SWJ (JTAG-DP + SW-DP): Reset State
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_SWJ(void)
{
  CLEAR_BIT(AFIO->MAPR,AFIO_MAPR_SWJ_CFG);
  SET_BIT(AFIO->MAPR, AFIO_MAPR_SWJ_CFG_RESET);
}

/**
  * @brief Enable the Serial wire JTAG configuration
  * @rmtoll MAPR          SWJ_CFG           LL_GPIO_AF_Remap_SWJ_NONJTRST
  * @note  NONJTRST: Full SWJ (JTAG-DP + SW-DP) but without NJTRST
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_Remap_SWJ_NONJTRST(void)
{
  CLEAR_BIT(AFIO->MAPR,AFIO_MAPR_SWJ_CFG);
  SET_BIT(AFIO->MAPR, AFIO_MAPR_SWJ_CFG_NOJNTRST);
}

/**
  * @brief Enable the Serial wire JTAG configuration
  * @rmtoll MAPR          SWJ_CFG           LL_GPIO_AF_Remap_SWJ_NOJTAG
  * @note  NOJTAG: JTAG-DP Disabled and SW-DP Enabled
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_Remap_SWJ_NOJTAG(void)
{
  CLEAR_BIT(AFIO->MAPR,AFIO_MAPR_SWJ_CFG);
  SET_BIT(AFIO->MAPR, AFIO_MAPR_SWJ_CFG_JTAGDISABLE);
}

/**
  * @brief Disable the Serial wire JTAG configuration
  * @rmtoll MAPR          SWJ_CFG           LL_GPIO_AF_DisableRemap_SWJ
  * @note  DISABLE: JTAG-DP Disabled and SW-DP Disabled
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_SWJ(void)
{
  CLEAR_BIT(AFIO->MAPR,AFIO_MAPR_SWJ_CFG);
  SET_BIT(AFIO->MAPR, AFIO_MAPR_SWJ_CFG_DISABLE);
}

#if defined(AFIO_MAPR_SPI3_REMAP)

/**
  * @brief Enable the remapping of SPI3 alternate functions SPI3_NSS/I2S3_WS, SPI3_SCK/I2S3_CK, SPI3_MISO, SPI3_MOSI/I2S3_SD.
  * @rmtoll MAPR          SPI3_REMAP           LL_GPIO_AF_EnableRemap_SPI3
  * @note  ENABLE: Remap     (SPI3_NSS-I2S3_WS/PA4,  SPI3_SCK-I2S3_CK/PC10, SPI3_MISO/PC11, SPI3_MOSI-I2S3_SD/PC12)
  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_SPI3(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_SPI3_REMAP | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Disable the remapping of SPI3 alternate functions SPI3_NSS/I2S3_WS, SPI3_SCK/I2S3_CK, SPI3_MISO, SPI3_MOSI/I2S3_SD.
  * @rmtoll MAPR          SPI3_REMAP           LL_GPIO_AF_DisableRemap_SPI3
  * @note  DISABLE: No remap (SPI3_NSS-I2S3_WS/PA15, SPI3_SCK-I2S3_CK/PB3,  SPI3_MISO/PB4,  SPI3_MOSI-I2S3_SD/PB5).
  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_SPI3(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_SPI3_REMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief  Check if SPI3 has been remaped or not
  * @rmtoll MAPR         SPI3_REMAP         LL_GPIO_AF_IsEnabledRemap_SPI3_REMAP
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_SPI3(void)
{
  return (READ_BIT(AFIO->MAPR, AFIO_MAPR_SPI3_REMAP) == (AFIO_MAPR_SPI3_REMAP));
}
#endif

#if defined(AFIO_MAPR_TIM2ITR1_IREMAP)

/**
  * @brief Control of TIM2_ITR1 internal mapping.
  * @rmtoll MAPR          TIM2ITR1_IREMAP           LL_GPIO_AF_Remap_TIM2ITR1_TO_USB
  * @note  TO_USB: Connect USB OTG SOF (Start of Frame) output to TIM2_ITR1 for calibration purposes.
  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_Remap_TIM2ITR1_TO_USB(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_TIM2ITR1_IREMAP | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Control of TIM2_ITR1 internal mapping.
  * @rmtoll MAPR          TIM2ITR1_IREMAP           LL_GPIO_AF_Remap_TIM2ITR1_TO_ETH
  * @note  TO_ETH: Connect TIM2_ITR1 internally to the Ethernet PTP output for calibration purposes.
  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_Remap_TIM2ITR1_TO_ETH(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_TIM2ITR1_IREMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}
#endif

#if defined(AFIO_MAPR_PTP_PPS_REMAP)

/**
  * @brief Enable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion).
  * @rmtoll MAPR          PTP_PPS_REMAP           LL_GPIO_AF_EnableRemap_ETH_PTP_PPS
  * @note  ENABLE: PTP_PPS is output on PB5 pin.
  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_ETH_PTP_PPS(void)
{
  SET_BIT(AFIO->MAPR, AFIO_MAPR_PTP_PPS_REMAP | AFIO_MAPR_SWJ_CFG);
}

/**
  * @brief Disable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion).
  * @rmtoll MAPR          PTP_PPS_REMAP           LL_GPIO_AF_DisableRemap_ETH_PTP_PPS
  * @note  DISABLE: PTP_PPS not output on PB5 pin.
  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_ETH_PTP_PPS(void)
{
  MODIFY_REG(AFIO->MAPR, (AFIO_MAPR_PTP_PPS_REMAP | AFIO_MAPR_SWJ_CFG), AFIO_MAPR_SWJ_CFG);
}
#endif

#if defined(AFIO_MAPR2_TIM9_REMAP)

/**
  * @brief Enable the remapping of TIM9_CH1 and TIM9_CH2.
  * @rmtoll MAPR2          TIM9_REMAP           LL_GPIO_AF_EnableRemap_TIM9
  * @note  ENABLE: Remap     (TIM9_CH1 on PE5 and TIM9_CH2 on PE6).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM9(void)
{
  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM9_REMAP);
}

/**
  * @brief Disable the remapping of TIM9_CH1 and TIM9_CH2.
  * @rmtoll MAPR2          TIM9_REMAP           LL_GPIO_AF_DisableRemap_TIM9
  * @note  DISABLE: No remap (TIM9_CH1 on PA2 and TIM9_CH2 on PA3).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM9(void)
{
  CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM9_REMAP);
}

/**
  * @brief  Check if TIM9_CH1 and TIM9_CH2 have been remaped or not
  * @rmtoll MAPR2         TIM9_REMAP         LL_GPIO_AF_IsEnabledRemap_TIM9
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_TIM9(void)
{
  return (READ_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM9_REMAP) == (AFIO_MAPR2_TIM9_REMAP));
}
#endif

#if defined(AFIO_MAPR2_TIM10_REMAP)

/**
  * @brief Enable the remapping of TIM10_CH1.
  * @rmtoll MAPR2          TIM10_REMAP           LL_GPIO_AF_EnableRemap_TIM10
  * @note  ENABLE: Remap     (TIM10_CH1 on PF6).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM10(void)
{
  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM10_REMAP);
}

/**
  * @brief Disable the remapping of TIM10_CH1.
  * @rmtoll MAPR2          TIM10_REMAP           LL_GPIO_AF_DisableRemap_TIM10
  * @note  DISABLE: No remap (TIM10_CH1 on PB8).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM10(void)
{
  CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM10_REMAP);
}

/**
  * @brief  Check if TIM10_CH1 has been remaped or not
  * @rmtoll MAPR2         TIM10_REMAP         LL_GPIO_AF_IsEnabledRemap_TIM10
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_TIM10(void)
{
  return (READ_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM10_REMAP) == (AFIO_MAPR2_TIM10_REMAP));
}
#endif

#if defined(AFIO_MAPR2_TIM11_REMAP)
/**
  * @brief Enable the remapping of TIM11_CH1.
  * @rmtoll MAPR2          TIM11_REMAP           LL_GPIO_AF_EnableRemap_TIM11
  * @note  ENABLE: Remap     (TIM11_CH1 on PF7).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM11(void)
{
  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM11_REMAP);
}

/**
  * @brief Disable the remapping of TIM11_CH1.
  * @rmtoll MAPR2          TIM11_REMAP           LL_GPIO_AF_DisableRemap_TIM11
  * @note  DISABLE: No remap (TIM11_CH1 on PB9).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM11(void)
{
  CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM11_REMAP);
}

/**
  * @brief  Check if TIM11_CH1 has been remaped or not
  * @rmtoll MAPR2         TIM11_REMAP         LL_GPIO_AF_IsEnabledRemap_TIM11
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_TIM11(void)
{
  return (READ_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM11_REMAP) == (AFIO_MAPR2_TIM11_REMAP));
}
#endif

#if defined(AFIO_MAPR2_TIM13_REMAP)

/**
  * @brief Enable the remapping of TIM13_CH1.
  * @rmtoll MAPR2          TIM13_REMAP           LL_GPIO_AF_EnableRemap_TIM13
  * @note  ENABLE: Remap     STM32F100:(TIM13_CH1 on PF8). Others:(TIM13_CH1 on PB0).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM13(void)
{
  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM13_REMAP);
}

/**
  * @brief Disable the remapping of TIM13_CH1.
  * @rmtoll MAPR2          TIM13_REMAP           LL_GPIO_AF_DisableRemap_TIM13
  * @note  DISABLE: No remap STM32F100:(TIM13_CH1 on PA6). Others:(TIM13_CH1 on PC8).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM13(void)
{
  CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM13_REMAP);
}

/**
  * @brief  Check if TIM13_CH1 has been remaped or not
  * @rmtoll MAPR2         TIM13_REMAP         LL_GPIO_AF_IsEnabledRemap_TIM13
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_TIM13(void)
{
  return (READ_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM13_REMAP) == (AFIO_MAPR2_TIM13_REMAP));
}
#endif

#if defined(AFIO_MAPR2_TIM14_REMAP)

/**
  * @brief Enable the remapping of TIM14_CH1.
  * @rmtoll MAPR2          TIM14_REMAP           LL_GPIO_AF_EnableRemap_TIM14
  * @note  ENABLE: Remap     STM32F100:(TIM14_CH1 on PB1). Others:(TIM14_CH1 on PF9).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM14(void)
{
  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM14_REMAP);
}

/**
  * @brief Disable the remapping of TIM14_CH1.
  * @rmtoll MAPR2          TIM14_REMAP           LL_GPIO_AF_DisableRemap_TIM14
  * @note  DISABLE: No remap STM32F100:(TIM14_CH1 on PC9). Others:(TIM14_CH1 on PA7).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM14(void)
{
  CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM14_REMAP);
}

/**
  * @brief  Check if TIM14_CH1 has been remaped or not
  * @rmtoll MAPR2         TIM14_REMAP         LL_GPIO_AF_IsEnabledRemap_TIM14
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_TIM14(void)
{
  return (READ_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM14_REMAP) == (AFIO_MAPR2_TIM14_REMAP));
}
#endif

#if defined(AFIO_MAPR2_FSMC_NADV_REMAP)

/**
  * @brief Controls the use of the optional FSMC_NADV signal.
  * @rmtoll MAPR2          FSMC_NADV           LL_GPIO_AF_Disconnect_FSMCNADV
  * @note  DISCONNECTED: The NADV signal is not connected. The I/O pin can be used by another peripheral.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_Disconnect_FSMCNADV(void)
{
  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_FSMC_NADV_REMAP);
}

/**
  * @brief Controls the use of the optional FSMC_NADV signal.
  * @rmtoll MAPR2          FSMC_NADV           LL_GPIO_AF_Connect_FSMCNADV
  * @note  CONNECTED: The NADV signal is connected to the output (default).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_Connect_FSMCNADV(void)
{
  CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_FSMC_NADV_REMAP);
}
#endif

#if defined(AFIO_MAPR2_TIM15_REMAP)

/**
  * @brief Enable the remapping of TIM15_CH1 and TIM15_CH2.
  * @rmtoll MAPR2          TIM15_REMAP           LL_GPIO_AF_EnableRemap_TIM15
  * @note  ENABLE: Remap     (TIM15_CH1 on PB14 and TIM15_CH2 on PB15).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM15(void)
{
  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM15_REMAP);
}
/**
  * @brief Disable the remapping of TIM15_CH1 and TIM15_CH2.
  * @rmtoll MAPR2          TIM15_REMAP           LL_GPIO_AF_DisableRemap_TIM15
  * @note  DISABLE: No remap (TIM15_CH1 on PA2  and TIM15_CH2 on PA3).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM15(void)
{
  CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM15_REMAP);
}

/**
  * @brief  Check if TIM15_CH1 has been remaped or not
  * @rmtoll MAPR2         TIM15_REMAP         LL_GPIO_AF_IsEnabledRemap_TIM15
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_TIM15(void)
{
  return (READ_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM15_REMAP) == (AFIO_MAPR2_TIM15_REMAP));
}
#endif

#if defined(AFIO_MAPR2_TIM16_REMAP)

/**
  * @brief Enable the remapping of TIM16_CH1.
  * @rmtoll MAPR2          TIM16_REMAP           LL_GPIO_AF_EnableRemap_TIM16
  * @note  ENABLE: Remap     (TIM16_CH1 on PA6).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM16(void)
{
  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM16_REMAP);
}

/**
  * @brief Disable the remapping of TIM16_CH1.
  * @rmtoll MAPR2          TIM16_REMAP           LL_GPIO_AF_DisableRemap_TIM16
  * @note  DISABLE: No remap (TIM16_CH1 on PB8).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM16(void)
{
  CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM16_REMAP);
}

/**
  * @brief  Check if TIM16_CH1 has been remaped or not
  * @rmtoll MAPR2         TIM16_REMAP         LL_GPIO_AF_IsEnabledRemap_TIM16
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_TIM16(void)
{
  return (READ_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM16_REMAP) == (AFIO_MAPR2_TIM16_REMAP));
}
#endif

#if defined(AFIO_MAPR2_TIM17_REMAP)

/**
  * @brief Enable the remapping of TIM17_CH1.
  * @rmtoll MAPR2          TIM17_REMAP           LL_GPIO_AF_EnableRemap_TIM17
  * @note  ENABLE: Remap     (TIM17_CH1 on PA7).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM17(void)
{
  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM17_REMAP);
}

/**
  * @brief Disable the remapping of TIM17_CH1.
  * @rmtoll MAPR2          TIM17_REMAP           LL_GPIO_AF_DisableRemap_TIM17
  * @note  DISABLE: No remap (TIM17_CH1 on PB9).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM17(void)
{
  CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM17_REMAP);
}

/**
  * @brief  Check if TIM17_CH1 has been remaped or not
  * @rmtoll MAPR2         TIM17_REMAP         LL_GPIO_AF_IsEnabledRemap_TIM17
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_TIM17(void)
{
  return (READ_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM17_REMAP) == (AFIO_MAPR2_TIM17_REMAP));
}
#endif

#if defined(AFIO_MAPR2_CEC_REMAP)

/**
  * @brief Enable the remapping of CEC.
  * @rmtoll MAPR2          CEC_REMAP           LL_GPIO_AF_EnableRemap_CEC
  * @note  ENABLE: Remap     (CEC on PB10).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_CEC(void)
{
  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_CEC_REMAP);
}

/**
  * @brief Disable the remapping of CEC.
  * @rmtoll MAPR2          CEC_REMAP           LL_GPIO_AF_DisableRemap_CEC
  * @note  DISABLE: No remap (CEC on PB8).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_CEC(void)
{
  CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_CEC_REMAP);
}

/**
  * @brief  Check if CEC has been remaped or not
  * @rmtoll MAPR2         CEC_REMAP         LL_GPIO_AF_IsEnabledRemap_CEC
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_CEC(void)
{
  return (READ_BIT(AFIO->MAPR2, AFIO_MAPR2_CEC_REMAP) == (AFIO_MAPR2_CEC_REMAP));
}
#endif

#if defined(AFIO_MAPR2_TIM1_DMA_REMAP)

/**
  * @brief Controls the mapping of the TIM1_CH1 TIM1_CH2 DMA requests onto the DMA1 channels.
  * @rmtoll MAPR2          TIM1_DMA_REMAP           LL_GPIO_AF_EnableRemap_TIM1DMA
  * @note  ENABLE: Remap (TIM1_CH1 DMA request/DMA1 Channel6, TIM1_CH2 DMA request/DMA1 Channel6)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM1DMA(void)
{
  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM1_DMA_REMAP);
}

/**
  * @brief Controls the mapping of the TIM1_CH1 TIM1_CH2 DMA requests onto the DMA1 channels.
  * @rmtoll MAPR2          TIM1_DMA_REMAP           LL_GPIO_AF_DisableRemap_TIM1DMA
  * @note  DISABLE: No remap (TIM1_CH1 DMA request/DMA1 Channel2, TIM1_CH2 DMA request/DMA1 Channel3).
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM1DMA(void)
{
  CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM1_DMA_REMAP);
}

/**
  * @brief  Check if TIM1DMA has been remaped or not
  * @rmtoll MAPR2         TIM1_DMA_REMAP         LL_GPIO_AF_IsEnabledRemap_TIM1DMA
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_TIM1DMA(void)
{
  return (READ_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM1_DMA_REMAP) == (AFIO_MAPR2_TIM1_DMA_REMAP));
}
#endif

#if defined(AFIO_MAPR2_TIM67_DAC_DMA_REMAP)

/**
  * @brief Controls the mapping of the TIM6_DAC1 and TIM7_DAC2 DMA requests onto the DMA1 channels.
  * @rmtoll MAPR2          TIM76_DAC_DMA_REMAP           LL_GPIO_AF_EnableRemap_TIM67DACDMA
  * @note  ENABLE: Remap (TIM6_DAC1 DMA request/DMA1 Channel3, TIM7_DAC2 DMA request/DMA1 Channel4)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM67DACDMA(void)
{
  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM67_DAC_DMA_REMAP);
}

/**
  * @brief Controls the mapping of the TIM6_DAC1 and TIM7_DAC2 DMA requests onto the DMA1 channels.
  * @rmtoll MAPR2          TIM76_DAC_DMA_REMAP           LL_GPIO_AF_DisableRemap_TIM67DACDMA
  * @note  DISABLE: No remap (TIM6_DAC1 DMA request/DMA2 Channel3, TIM7_DAC2 DMA request/DMA2 Channel4)
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM67DACDMA(void)
{
  CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM67_DAC_DMA_REMAP);
}

/**
  * @brief  Check if TIM67DACDMA has been remaped or not
  * @rmtoll MAPR2         TIM76_DAC_DMA_REMAP         LL_GPIO_AF_IsEnabledRemap_TIM67DACDMA
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_TIM67DACDMA(void)
{
  return (READ_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM67_DAC_DMA_REMAP) == (AFIO_MAPR2_TIM67_DAC_DMA_REMAP));
}
#endif

#if defined(AFIO_MAPR2_TIM12_REMAP)

/**
  * @brief Enable the remapping of TIM12_CH1 and TIM12_CH2.
  * @rmtoll MAPR2          TIM12_REMAP           LL_GPIO_AF_EnableRemap_TIM12
  * @note  ENABLE: Remap     (TIM12_CH1 on PB12 and TIM12_CH2 on PB13).
  * @note  This bit is available only in high density value line devices.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_TIM12(void)
{
  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM12_REMAP);
}

/**
  * @brief Disable the remapping of TIM12_CH1 and TIM12_CH2.
  * @rmtoll MAPR2          TIM12_REMAP           LL_GPIO_AF_DisableRemap_TIM12
  * @note  DISABLE: No remap (TIM12_CH1 on PC4  and TIM12_CH2 on PC5).
  * @note  This bit is available only in high density value line devices.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_TIM12(void)
{
  CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM12_REMAP);
}

/**
  * @brief  Check if TIM12_CH1 has been remaped or not
  * @rmtoll MAPR2         TIM12_REMAP         LL_GPIO_AF_IsEnabledRemap_TIM12
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_TIM12(void)
{
  return (READ_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM12_REMAP) == (AFIO_MAPR2_TIM12_REMAP));
}
#endif

#if defined(AFIO_MAPR2_MISC_REMAP)

/**
  * @brief Miscellaneous features remapping.
  *        This bit is set and cleared by software. It controls miscellaneous features.
  *        The DMA2 channel 5 interrupt position in the vector table.
  *        The timer selection for DAC trigger 3 (TSEL[2:0] = 011, for more details refer to the DAC_CR register).
  * @rmtoll MAPR2          MISC_REMAP           LL_GPIO_AF_EnableRemap_MISC
  * @note  ENABLE: DMA2 channel 5 interrupt is mapped separately at position 60 and TIM15 TRGO event is
  *        selected as DAC Trigger 3, TIM15 triggers TIM1/3.
  * @note  This bit is available only in high density value line devices.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableRemap_MISC(void)
{
  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_MISC_REMAP);
}

/**
  * @brief Miscellaneous features remapping.
  *        This bit is set and cleared by software. It controls miscellaneous features.
  *        The DMA2 channel 5 interrupt position in the vector table.
  *        The timer selection for DAC trigger 3 (TSEL[2:0] = 011, for more details refer to the DAC_CR register).
  * @rmtoll MAPR2          MISC_REMAP           LL_GPIO_AF_DisableRemap_MISC
  * @note  DISABLE: DMA2 channel 5 interrupt is mapped with DMA2 channel 4 at position 59, TIM5 TRGO
  *        event is selected as DAC Trigger 3, TIM5 triggers TIM1/3.
  * @note  This bit is available only in high density value line devices.
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableRemap_MISC(void)
{
  CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_MISC_REMAP);
}

/**
  * @brief  Check if MISC has been remaped or not
  * @rmtoll MAPR2         MISC_REMAP         LL_GPIO_AF_IsEnabledRemap_MISC
  * @retval State of bit (1 or 0).
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_IsEnabledRemap_MISC(void)
{
  return (READ_BIT(AFIO->MAPR2, AFIO_MAPR2_MISC_REMAP) == (AFIO_MAPR2_MISC_REMAP));
}
#endif

/**
  * @}
  */

/** @defgroup GPIO_AF_LL_EVENTOUT Output Event configuration
  * @brief This section propose definition to Configure EVENTOUT Cortex feature .
  * @{
  */

/**
  * @brief  Configures the port and pin on which the EVENTOUT Cortex signal will be connected.
  * @rmtoll EVCR          PORT           LL_GPIO_AF_ConfigEventout\n
  *         EVCR          PIN            LL_GPIO_AF_ConfigEventout
  * @param  LL_GPIO_PortSource This parameter can be one of the following values:
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PORT_A
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PORT_B
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PORT_C
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PORT_D
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PORT_E
  * @param  LL_GPIO_PinSource This parameter can be one of the following values:
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_0
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_1
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_2
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_3
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_4
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_5
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_6
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_7
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_8
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_9
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_10
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_11
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_12
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_13
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_14
  *      @arg @ref LL_GPIO_AF_EVENTOUT_PIN_15
  * @retval None
*/
__STATIC_INLINE void LL_GPIO_AF_ConfigEventout(uint32_t LL_GPIO_PortSource, uint32_t LL_GPIO_PinSource)
{
  MODIFY_REG(AFIO->EVCR, (AFIO_EVCR_PORT) | (AFIO_EVCR_PIN), (LL_GPIO_PortSource) | (LL_GPIO_PinSource));
}

/**
  * @brief  Enables the Event Output.
  * @rmtoll EVCR          EVOE           LL_GPIO_AF_EnableEventout
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_EnableEventout(void)
{
  SET_BIT(AFIO->EVCR, AFIO_EVCR_EVOE);
}

/**
  * @brief  Disables the Event Output.
  * @rmtoll EVCR          EVOE           LL_GPIO_AF_DisableEventout
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_DisableEventout(void)
{
  CLEAR_BIT(AFIO->EVCR, AFIO_EVCR_EVOE);
}

/**
  * @}
  */
/** @defgroup GPIO_AF_LL_EXTI EXTI external interrupt
  * @brief This section Configure source input for the EXTI external interrupt .
  * @{
  */

/**
  * @brief  Configure source input for the EXTI external interrupt.
  * @rmtoll AFIO_EXTICR1      EXTIx         LL_GPIO_AF_SetEXTISource\n
  *         AFIO_EXTICR2      EXTIx         LL_GPIO_AF_SetEXTISource\n
  *         AFIO_EXTICR3      EXTIx         LL_GPIO_AF_SetEXTISource\n
  *         AFIO_EXTICR4      EXTIx         LL_GPIO_AF_SetEXTISource
  * @param  Port This parameter can be one of the following values:
  *         @arg @ref LL_GPIO_AF_EXTI_PORTA
  *         @arg @ref LL_GPIO_AF_EXTI_PORTB
  *         @arg @ref LL_GPIO_AF_EXTI_PORTC
  *         @arg @ref LL_GPIO_AF_EXTI_PORTD
  *         @arg @ref LL_GPIO_AF_EXTI_PORTE
  *         @arg @ref LL_GPIO_AF_EXTI_PORTF
  *         @arg @ref LL_GPIO_AF_EXTI_PORTG
  * @param  Line This parameter can be one of the following values:
  *         @arg @ref LL_GPIO_AF_EXTI_LINE0
  *         @arg @ref LL_GPIO_AF_EXTI_LINE1
  *         @arg @ref LL_GPIO_AF_EXTI_LINE2
  *         @arg @ref LL_GPIO_AF_EXTI_LINE3
  *         @arg @ref LL_GPIO_AF_EXTI_LINE4
  *         @arg @ref LL_GPIO_AF_EXTI_LINE5
  *         @arg @ref LL_GPIO_AF_EXTI_LINE6
  *         @arg @ref LL_GPIO_AF_EXTI_LINE7
  *         @arg @ref LL_GPIO_AF_EXTI_LINE8
  *         @arg @ref LL_GPIO_AF_EXTI_LINE9
  *         @arg @ref LL_GPIO_AF_EXTI_LINE10
  *         @arg @ref LL_GPIO_AF_EXTI_LINE11
  *         @arg @ref LL_GPIO_AF_EXTI_LINE12
  *         @arg @ref LL_GPIO_AF_EXTI_LINE13
  *         @arg @ref LL_GPIO_AF_EXTI_LINE14
  *         @arg @ref LL_GPIO_AF_EXTI_LINE15
  * @retval None
  */
__STATIC_INLINE void LL_GPIO_AF_SetEXTISource(uint32_t Port, uint32_t Line)
{
  MODIFY_REG(AFIO->EXTICR[Line & 0xFF], (Line >> 16), Port << POSITION_VAL((Line >> 16)));
}

/**
  * @brief  Get the configured defined for specific EXTI Line
  * @rmtoll AFIO_EXTICR1      EXTIx         LL_GPIO_AF_GetEXTISource\n
  *         AFIO_EXTICR2      EXTIx         LL_GPIO_AF_GetEXTISource\n
  *         AFIO_EXTICR3      EXTIx         LL_GPIO_AF_GetEXTISource\n
  *         AFIO_EXTICR4      EXTIx         LL_GPIO_AF_GetEXTISource
  * @param  Line This parameter can be one of the following values:
  *         @arg @ref LL_GPIO_AF_EXTI_LINE0
  *         @arg @ref LL_GPIO_AF_EXTI_LINE1
  *         @arg @ref LL_GPIO_AF_EXTI_LINE2
  *         @arg @ref LL_GPIO_AF_EXTI_LINE3
  *         @arg @ref LL_GPIO_AF_EXTI_LINE4
  *         @arg @ref LL_GPIO_AF_EXTI_LINE5
  *         @arg @ref LL_GPIO_AF_EXTI_LINE6
  *         @arg @ref LL_GPIO_AF_EXTI_LINE7
  *         @arg @ref LL_GPIO_AF_EXTI_LINE8
  *         @arg @ref LL_GPIO_AF_EXTI_LINE9
  *         @arg @ref LL_GPIO_AF_EXTI_LINE10
  *         @arg @ref LL_GPIO_AF_EXTI_LINE11
  *         @arg @ref LL_GPIO_AF_EXTI_LINE12
  *         @arg @ref LL_GPIO_AF_EXTI_LINE13
  *         @arg @ref LL_GPIO_AF_EXTI_LINE14
  *         @arg @ref LL_GPIO_AF_EXTI_LINE15
  * @retval Returned value can be one of the following values:
  *         @arg @ref LL_GPIO_AF_EXTI_PORTA
  *         @arg @ref LL_GPIO_AF_EXTI_PORTB
  *         @arg @ref LL_GPIO_AF_EXTI_PORTC
  *         @arg @ref LL_GPIO_AF_EXTI_PORTD
  *         @arg @ref LL_GPIO_AF_EXTI_PORTE
  *         @arg @ref LL_GPIO_AF_EXTI_PORTF
  *         @arg @ref LL_GPIO_AF_EXTI_PORTG
  */
__STATIC_INLINE uint32_t LL_GPIO_AF_GetEXTISource(uint32_t Line)
{
  return (uint32_t)(READ_BIT(AFIO->EXTICR[Line & 0xFF], (Line >> 16)) >> POSITION_VAL(Line >> 16));
}

/**
  * @}
  */

#if defined(USE_FULL_LL_DRIVER)
/** @defgroup GPIO_LL_EF_Init Initialization and de-initialization functions
  * @{
  */

ErrorStatus LL_GPIO_DeInit(GPIO_TypeDef *GPIOx);
ErrorStatus LL_GPIO_Init(GPIO_TypeDef *GPIOx, LL_GPIO_InitTypeDef *GPIO_InitStruct);
void        LL_GPIO_StructInit(LL_GPIO_InitTypeDef *GPIO_InitStruct);

/**
  * @}
  */
#endif /* USE_FULL_LL_DRIVER */

/**
  * @}
  */

/**
  * @}
  */

#endif /* defined (GPIOA) || defined (GPIOB) || defined (GPIOC) || defined (GPIOD) || defined (GPIOE) || defined (GPIOF) || defined (GPIOG) */
/**
  * @}
  */

#ifdef __cplusplus
}
#endif

#endif /* STM32F1xx_LL_GPIO_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/